DeWalt DWE7491 Saw Blades Fig, Splitter and Riving Knife Selection Fig, Plate under Assembly

Page 10

English

POSITION 2 FENCE ALIGNMENT (FIG. 22, 23)

1.To align position 2 fence locator pins, ensure position 1 pins have been aligned, refer to Position 1 Fence Alignment.

2.Loosen the position 2 locator pins, then using the blade wrench holes as a guide for positioning, align the pins (Fig. 23).

3.Tighten the locator pins (front and rear).

FIG. 23 DD

 

U

 

ALIGNING RIVING KNIFE TO BLADE (FIG. 24)

 

1.

Remove the throat plate. Refer to Remove Throat

FIG. 24

 

Plate under Assembly.

 

 

2.

Raise the blade to full depth of cut and 0° bevel

PP

 

angle.

3.

Locate the three small set screws (PP) adjacent to

 

 

the riving knife lock knob (QQ). These screws will

 

 

be used to adjust the riving knife position.

 

4.

Lay a straight edge on the table against two blade

QQ

 

tips. The riving knife should not touch the straight

 

 

edge. If needed, loosen the two larger lock screws

 

 

(RR).

 

5.

Adjust the small set screws (PP) to move the riving

 

 

knife according to the position noted in step 5. Lay

RR

 

the straight edge on the opposite side of the blade

 

 

and repeat adjustments as needed.

 

6.Lightly tighten the two larger lock screws (RR).

7.Place a square flat against the riving knife to verify the riving knife is vertical and in-line with the blade.

8.If needed, use the set screws to bring the riving knife vertical with the square.

9.Repeat steps 5 and 6 to verify position of riving knife.

10.Fully tighten the two larger lock screws (RR).

Saw Blades (Fig. 25)

WARNING: Riving knives must be matched to saw blade dimensions in order to function effectively. Refer to Riving Knife Selection.

NOTE: THIS SAW IS INTENDED FOR USE ONLY WITH SAW BLADES 10" (254 mm) IN DIAMETER.

FIG. 25

The saw blade furnished with your new saw is a 10" (254 mm) combination blade, used for crosscutting (across the grain) and ripping (with the grain) through the material. The center hole to fit on the arbor is 5/8" (16 mm) diameter. This blade will produce a good quality cut for most applications.

There are many types of blades available to do specific and special jobs such as cross cut only, rip only, hollow ground, thin plywood, paneling, etc.

Use only saw blades designed for maximum safe operating speeds of 5,000 RPM or greater.

Saw blades should always be kept sharp. It is recommended that you locate a reputable sharpening service to sharpen your blades when needed.

Never stack blades on top of one another to store. Place material such as cardboard between them to keep the blades from coming in contact with one another.

CAUTION: To reduce the risk of injury, abrasive wheels or blades (including diamond) should not be used on this saw.

Splitter and Riving Knife Selection (Fig. 26–28)

WARNING: To minimize the risk of kickback and to ensure proper cutting, the splitter and riving knife must be the proper thickness for the blade used.

The splitter and riving knife supplied with this table saw is the correct size for the blade supplied with the saw.

If a different blade is used, check the blade body (plate) thickness and the blade kerf (cutting) width marked on the blade or on the blade packaging. The splitter and riving knife thickness must be greater than the body thickness and less than the kerf width as shown in Figure 26.

FIG. 26

RIVING KNIFE

 

THICKNESS

KERF WIDTH

(WIDTH OF CUT MADE BY THE BLADE)

BODY (OR PLATE)

THICKNESS OF THE

BLADE

8

Image 10
Contents Dewalt Page Important Safety Instructions Definitions Safety GuidelinesGeneral Safety Rules Double Insulation Polarized PlugsAdditional Safety Rules for Table Saws Always lock the fence and bevel adjustment before cuttingMaking a Push Stick Inside Back Cover KickbacksUnpacking Fig FeaturesSave These Instructions for Future USE Specifications Amperes 15 a Table SizeThis SAW should be Assembled in the Following Order FIG, 2 AssemblyTo remove the blade guard assembly/riving knife ATTACHING/REPLACING the BladeBench Mounting Connecting Saw to Power Source AdjustmentsSplitter and Riving Knife Selection Fig Plate under AssemblySaw Blades Fig Position 2 Fence AlignmentKickback OperationRip Fence Operation On-Off Switch FigGuard Operating Feature Fig Ripping FigNarrow Rip Auxiliary Fence Ripping Small Pieces FigPush Block Bevel Crosscutting Bevel RippingCrosscutting Mitering FigFeatherboard Construction Miter Gauge OperationDado Cutting Dust Collection FigCleaning Motor Overload and Power Loss Reset SwitchMaintenance Lubrication FigYear Free Service Accessories RepairsThree Year Limited Warranty DAY Money Back GuaranteeConserver CES Consignes Définitions lignes directrices en Matière de sécuritéRègles de sécurité Généralités Double isolationFrançais Rebonds Caractéristiques techniques Conserver CES Consignes Pour Utilisation UltérieureDéballage Fig Usage Prévu DescriptionMontage Cette Scie Doit Être Assemblée Dans L’ORDRE SuivantPour positionner le dispositif de carter de lame INSTALLATION/REMPLACEMENT DE LA LamePour Installer LA Plaque DE Lumière FIG Retrait du dispositif de carter de lame/couteau diviseurRetrait DE LA Plaque DE Lumière DWE7490 Installation DU Guide LongitudinalDWE7491 Installation DU Guide Longitudinal FIG Dispositif ANTI-REBONDSBranchement de la scie sur le secteur Fixation sur établiRéglages Position 1 D’ALIGNEMENT DE Guide FIG Lames de scie FigRéglage DU Guide D’ONGLET FIG Position 2 D’ALIGNEMENT DE GuideSélection du couteau séparateur et couteau diviseur à Interrupteur marche/arrêt Fig RebondsUtilisation Fonctionnalité du dispositif de protection FigUtilisation du guide longitudinal Coupe longitudinale FigBloc-poussoir Coupes longitudinales de petites pièces FigGuide longitudinal auxiliaire étroit Coupes transversales en biseau Taille en biseauCoupes transversales Onglet FigConstruction d’un peigne Utilisation du guide d’ongletEngravure Onglet MixteStockage à Système de dépoussiérage FigLubrification Fig Position d’ARRÊTRéparations AccessoiresNettoyage Registre en ligneXXX Doble Aislamiento Definiciones Normas de seguridadGuarde Estas Instrucciones Instrucciones Importantes de SeguridadReglas de Seguridad Adicionales para Sierras de Banco Los accesorios magnéticos no funcionan con esta sierraBloquee Siempre la guía y el ajuste de bisel antes de cortar RebotesComponentes Guarde Estas Instrucciones Para Futuras ConsultasDesembalaje Fig EspecificacionesEsta Sierra Debe SER Ensamblada Siguiendo Este Orden MontajeUSO Debido INSTALACIÓN/CAMBIO DE LA HojaEnsamblaje DE LA Placa DE Garganta FIG Para posicionar la unidad del protector de la hojaLevante el eje de la hoja de sierra hasta su altura máxima Sacar LA Placa DE GargantaConectar la sierra a la fuente de alimentación Montaje en bancoUnidad ANTI-REBOTE Ajuste DEL Tope E Indicador DE Bisel AjustesAjuste DE LA Escala DE Ranura Ajuste DE LA Alineación DE LA GuíaAlineamiento DE LA Guía EN Posición 2 Hojas de Sierra FigSelección de placa abridora y cuchillo divisor Alineación DE LA Cuchilla CON LA Hoja FIGRebote OperaciónInstrucciones DE LA Característica DE Bloqueo Característica de funcionamiento del protector FigPalanca DE Bloqueo DEL Riel FIG Pomo DE Ajuste FIGRealizar cortes longitudinales Fig Corte longitudinal de trozos pequeños FigCorte Cruzado Bloque de EmpujeCorte longitudinal biselado De la guíaRanurado Corte Cruzado de BiselInglete Fig Ingleteado CompuestoLubricación Fig Consulte la FiguraLimpieza Almacenamiento FigMantenimiento AccesoriosRegistro en línea ReparacionesPóliza de Garantía Garantía limitada por tres añosGarantía DE Reembolso DE SU Dinero POR 90 Días Especificaciones DWE7490, DWE7491Page Page Copyright 2013 D Ewalt

DWE7490, DWE7491 specifications

The DeWalt DWE7491 and DWE7490 are two highly regarded table saws in the woodworking community, revered for their performance, versatility, and advanced features. These saws are designed to cater to both professional woodworkers and DIY enthusiasts, making them ideal for a variety of applications.

One of the standout features of the DeWalt DWE7491 is its innovative Rack and Pinion telescoping fence system. This system allows users to easily make accurate adjustments for precise cuts and ensures that the fence remains parallel to the blade. The fence can extend up to 32 inches, providing ample support for larger materials. This is especially useful when working with sheet goods or larger workpieces, making it a valuable tool on the job site.

The DWE7491 also boasts a powerful 2,000-watt motor that delivers a no-load speed of 4,800 RPM. This high speed allows for smooth, clean cuts through various materials, including hardwood and softwood. The saw's 10-inch blade is capable of cutting through thick materials with ease, while a blade guard and anti-kickback pawls enhance safety during operation.

Equipped with a portable design, the DWE7491 and DWE7490 feature onboard storage for accessories, which helps keep the workspace organized. Both models come with heavy-duty wheels for easy transportation, making them practical for job sites where mobility is essential.

In terms of technology, the DWE7490 model includes a patented Site-Pro Modular Guarding System, which provides the flexibility to adapt to different cutting applications. This system allows users to make quick adjustments to the guard and the riving knife, enhancing user safety while maintaining cutting performance.

Both models offer solid stability due to their durable construction and integrated stand, reducing vibrations and ensuring accurate cuts. The DWE7491 and DWE7490 also feature a large, sturdy surface area, providing ample workspace for materials while enhancing overall safety during operation.

With their advanced features, powerful motors, and portability, the DeWalt DWE7491 and DWE7490 have made a significant impact in the woodworking industry. They cater to various cutting needs, making them valuable investments for anyone looking to enhance their woodworking capabilities.