DeWalt DWE7490, DWE7491 instruction manual Making a Push Stick Inside Back Cover, Kickbacks

Page 5

TERMS: THE FOLLOWING TERMS WILL BE USED THROUGHOUT THE MANUAL AND YOU SHOULD BECOME FAMILIAR WITH THEM.

•Thru-sawingrefers to any cut that completely cuts through the workpiece.

•Non thru-sawingrefers to any cut that does not completely cut through the workpiece.

•Push Stick refers to a wooden or plastic stick, usually homemade, that is used to push small workpiece through the saw and keeps the operator’s hands clear of the blade.

•Kickback occurs when the saw blade binds in the cut and violently thrusts the workpiece back toward the operator.

•Freehand refers to cutting without the use of a miter gauge or rip fence or any other means of guiding or holding the workpiece other than the operator’s hands.

WARNING: Never perform freehand cutting with this saw.

•Plunge cutting refers to cutting where the workpiece is either lowered down onto the blade with the workpiece controlled by the user's hands or the workpiece is supported by the user's hands on the table surface and the blade is then raised up through the workpiece.

WARNING: Never perform plunge cutting with this saw.

•Resawing - Flipping material to make a cut the saw is not capable of making in one pass. WARNING: Resawing IS NOT recommended.

•Outfeed - The distance behind the saw required to pass the material all the way through the cut.

SAW BLADE GUARD ASSEMBLY, ANTI-KICKBACK ASSEMBLY AND RIVING KNIFE

This table saw is equipped with a blade guard assembly with splitter and anti-kickback assembly that covers the blade and reduces the possibility of accidental blade contact. A non thru-sawing riving knife is also provided when making non thru-cuts. The riving knife and splitter are flat plates that fit into the cut made by the saw blade and effectively fights kickback by lessening the tendency of the blade to bind in the cut. The blade guard assembly and anti-kickback assembly can only be used when making thru-cuts that sever the wood. When making rabbets and other cuts that make non thru-cuts, the blade guard assembly and anti-kickback assembly must be removed and then install the non thru-sawing riving knife provided. Two anti-kickback pawls are located on the sides of the riving knife that allow the wood to pass through the blade in the cutting direction but reduce the possibility of the material being thrown backwards toward the operator.

Use all components of the guarding system (blade guard assembly, riving knife and anti- kickback assembly) for every operation for which they can be used including all thru-cutting. If you elect not to use any of these components for a particular application exercise additional caution regarding control of the workpiece, the use of push sticks, the position of your hands relative to the blade, the use of safety glasses, the means to avoid kickback and all other warnings contained in this manual and on the saw itself. Replace the guarding systems as soon as you return to thru-cutting operations. Keep the guard assembly in working order.

MAKING A PUSH STICK (Inside Back Cover)

•In order to operate this table saw safely you must use a push stick whenever the size or shape of the workpiece would cause your hands to be within 6" (152 mm) of the saw blade or other cutter. A push stick is included with this saw.

•No special wood is needed to make additional push-sticks as long as it’s sturdy and long enough. A length of 15.7" (400 mm) is recommended with a notch that fits against the edge of the workpiece to prevent slipping. It’s a good idea to have several push sticks of the same length (15.7" [400 mm] ) with different size notches for different workpiece thicknesses.

•See the inside back cover for a picture of a push stick. The shape can vary to suit your own needs as long as it performs its intended function of keeping your hands away from the blade.

KICKBACKS

Kickbacks can cause serious injury. A kickback occurs when a part of the workpiece binds between the saw blade and the rip fence, or other fixed object, and rises from the table and is thrown toward the operator. Kickbacks can be avoided by attention to the following conditions.

How to Avoid Them and Protect Yourself from Possible Injury

a.Use the blade guard with splitter, or use the riving knife whenever possible.

b.Be certain that the rip fence is parallel to the saw blade.

c.Do not rip by applying the feed force to the section of the workpiece that will become the cut-off (free) piece. Feed force when ripping should always be applied between the saw blade and the fence; use a push stick for narrow work, 6" (152 mm) wide or less.

d.Keep saw blade guard assembly, riving knife and anti-kickback assembly in place and operating properly. If anti-kickback assembly is not operational, return your unit to the nearest authorized DEWALT service center for repair. The splitter and riving knife must be in alignment with the saw blade and the anti-kickback assembly must stop a kickback once it has started. Check their action before ripping by pushing the wood under the anti-kickback assembly. The teeth must prevent the wood from being pulled toward the front of the saw.

e.Plastic and composite (like laminate flooring) materials may be cut on this saw. However, since these are usually quite hard and slippery, the anti-kickback pawls may not stop a kickback. Therefore, be especially attentive to following proper set up and cutting procedures for ripping.

f.Use saw blade guard assembly, anti-kickback assembly and riving knife for every operation for which it can be used, including all thru-sawing.

g.Push the workpiece past the saw blade prior to release.

h.NEVER rip a workpiece that is twisted or warped, or does not have a straight edge to guide along the fence.

i.NEVER saw a large workpiece that cannot be controlled.

j.NEVER use the fence as a guide or length stop when crosscutting.

k.NEVER saw a workpiece with loose knots, flaws, nails or other foreign objects.

l.NEVER rip a workpiece shorter than 10" (254 mm).

m.NEVER use a dull blade – replace or have resharpened.

WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses. Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:

•ANSI Z87.1 eye protection (CAN/CSA Z94.3),

•ANSI S12.6 (S3.19) hearing protection,

•NIOSH/OSHA/MSHA respiratory protection.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

•lead from lead-based paints,

•crystalline silica from bricks and cement and other masonry products, and

•arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

•Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of harmful chemicals.

English

3

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Dewalt Page General Safety Rules Double Insulation Definitions Safety GuidelinesImportant Safety Instructions Polarized PlugsAlways lock the fence and bevel adjustment before cutting Additional Safety Rules for Table SawsKickbacks Making a Push Stick Inside Back CoverSave These Instructions for Future USE Specifications FeaturesUnpacking Fig Amperes 15 a Table SizeTo remove the blade guard assembly/riving knife AssemblyThis SAW should be Assembled in the Following Order FIG, 2 ATTACHING/REPLACING the BladeBench Mounting Adjustments Connecting Saw to Power SourceSaw Blades Fig Plate under AssemblySplitter and Riving Knife Selection Fig Position 2 Fence AlignmentOperation KickbackGuard Operating Feature Fig On-Off Switch FigRip Fence Operation Ripping FigPush Block Ripping Small Pieces FigNarrow Rip Auxiliary Fence Crosscutting Bevel RippingBevel Crosscutting Mitering FigDado Cutting Miter Gauge OperationFeatherboard Construction Dust Collection FigMaintenance Motor Overload and Power Loss Reset SwitchCleaning Lubrication FigThree Year Limited Warranty Accessories RepairsYear Free Service DAY Money Back GuaranteeRègles de sécurité Généralités Définitions lignes directrices en Matière de sécuritéConserver CES Consignes Double isolationFrançais Rebonds Déballage Fig Conserver CES Consignes Pour Utilisation UltérieureCaractéristiques techniques Montage DescriptionUsage Prévu Cette Scie Doit Être Assemblée Dans L’ORDRE SuivantPour Installer LA Plaque DE Lumière FIG INSTALLATION/REMPLACEMENT DE LA LamePour positionner le dispositif de carter de lame Retrait du dispositif de carter de lame/couteau diviseurDWE7491 Installation DU Guide Longitudinal FIG DWE7490 Installation DU Guide LongitudinalRetrait DE LA Plaque DE Lumière Dispositif ANTI-REBONDSRéglages Fixation sur établiBranchement de la scie sur le secteur Réglage DU Guide D’ONGLET FIG Lames de scie FigPosition 1 D’ALIGNEMENT DE Guide FIG Position 2 D’ALIGNEMENT DE GuideSélection du couteau séparateur et couteau diviseur à Utilisation RebondsInterrupteur marche/arrêt Fig Fonctionnalité du dispositif de protection FigCoupe longitudinale Fig Utilisation du guide longitudinalGuide longitudinal auxiliaire étroit Coupes longitudinales de petites pièces FigBloc-poussoir Coupes transversales Taille en biseauCoupes transversales en biseau Onglet FigEngravure Utilisation du guide d’ongletConstruction d’un peigne Onglet MixteLubrification Fig Système de dépoussiérage FigStockage à Position d’ARRÊTNettoyage AccessoiresRéparations Registre en ligneXXX Guarde Estas Instrucciones Definiciones Normas de seguridadDoble Aislamiento Instrucciones Importantes de SeguridadLos accesorios magnéticos no funcionan con esta sierra Reglas de Seguridad Adicionales para Sierras de BancoRebotes Bloquee Siempre la guía y el ajuste de bisel antes de cortarDesembalaje Fig Guarde Estas Instrucciones Para Futuras ConsultasComponentes EspecificacionesUSO Debido MontajeEsta Sierra Debe SER Ensamblada Siguiendo Este Orden INSTALACIÓN/CAMBIO DE LA HojaLevante el eje de la hoja de sierra hasta su altura máxima Para posicionar la unidad del protector de la hojaEnsamblaje DE LA Placa DE Garganta FIG Sacar LA Placa DE GargantaUnidad ANTI-REBOTE Montaje en bancoConectar la sierra a la fuente de alimentación Ajuste DE LA Escala DE Ranura AjustesAjuste DEL Tope E Indicador DE Bisel Ajuste DE LA Alineación DE LA GuíaSelección de placa abridora y cuchillo divisor Hojas de Sierra FigAlineamiento DE LA Guía EN Posición 2 Alineación DE LA Cuchilla CON LA Hoja FIGOperación RebotePalanca DE Bloqueo DEL Riel FIG Característica de funcionamiento del protector FigInstrucciones DE LA Característica DE Bloqueo Pomo DE Ajuste FIGCorte longitudinal de trozos pequeños Fig Realizar cortes longitudinales FigCorte longitudinal biselado Bloque de EmpujeCorte Cruzado De la guíaInglete Fig Corte Cruzado de BiselRanurado Ingleteado CompuestoConsulte la Figura Lubricación FigMantenimiento Almacenamiento FigLimpieza AccesoriosPóliza de Garantía ReparacionesRegistro en línea Garantía limitada por tres añosEspecificaciones DWE7490, DWE7491 Garantía DE Reembolso DE SU Dinero POR 90 DíasPage Page Copyright 2013 D Ewalt

DWE7490, DWE7491 specifications

The DeWalt DWE7491 and DWE7490 are two highly regarded table saws in the woodworking community, revered for their performance, versatility, and advanced features. These saws are designed to cater to both professional woodworkers and DIY enthusiasts, making them ideal for a variety of applications.

One of the standout features of the DeWalt DWE7491 is its innovative Rack and Pinion telescoping fence system. This system allows users to easily make accurate adjustments for precise cuts and ensures that the fence remains parallel to the blade. The fence can extend up to 32 inches, providing ample support for larger materials. This is especially useful when working with sheet goods or larger workpieces, making it a valuable tool on the job site.

The DWE7491 also boasts a powerful 2,000-watt motor that delivers a no-load speed of 4,800 RPM. This high speed allows for smooth, clean cuts through various materials, including hardwood and softwood. The saw's 10-inch blade is capable of cutting through thick materials with ease, while a blade guard and anti-kickback pawls enhance safety during operation.

Equipped with a portable design, the DWE7491 and DWE7490 feature onboard storage for accessories, which helps keep the workspace organized. Both models come with heavy-duty wheels for easy transportation, making them practical for job sites where mobility is essential.

In terms of technology, the DWE7490 model includes a patented Site-Pro Modular Guarding System, which provides the flexibility to adapt to different cutting applications. This system allows users to make quick adjustments to the guard and the riving knife, enhancing user safety while maintaining cutting performance.

Both models offer solid stability due to their durable construction and integrated stand, reducing vibrations and ensuring accurate cuts. The DWE7491 and DWE7490 also feature a large, sturdy surface area, providing ample workspace for materials while enhancing overall safety during operation.

With their advanced features, powerful motors, and portability, the DeWalt DWE7491 and DWE7490 have made a significant impact in the woodworking industry. They cater to various cutting needs, making them valuable investments for anyone looking to enhance their woodworking capabilities.
Top Page Image Contents