Country Home Products 10 HP manual Grease Fittings, Supplies Needed

Page 30

Grease Fittings

Your DR 10 HP CHIPPER was greased at the Factory. The operator needs to lubricate the Chipper Side and Drive Side Bearings periodically.

BEFORE PERFORMING ANY MAINTENANCE PROCEDURE OR INSPECTION, STOP THE ENGINE, WAIT FIVE

(5)MINUTES TO ALLOW ALL MOVING PARTS TO COME TO A COMPLETE STOP AND COOL. DISCONNECT THE SPARK PLUG WIRE, KEEPING IT AWAY FROM THE SPARK PLUG.

Supplies Needed:

•Flexible hose grease gun

•Lithium grease

•Clean cloth

•5/32" Allen Wrench

•Loctite® 243 (if needed)

1.Wipe all dirt, etc., from the grease fittings with a clean cloth (Figure 6).

2.Apply no more than three (3) pumps of quality general-purpose lithium grease with a hand- pumped grease gun to each grease fitting, one (1) on the Chipper Side Bearing, and one (1) on the Drive Side Bearing.

OVER LUBRICATION CAN ALSO DAMAGE THE BEARINGS.

3.After greasing, check the Side Bearing Collar Set Screws for tightness with a 5/32" Allen Wrench. If they are loose, reset them with Loctite® 243, obtainable at any hardware store.

Side Bearing Collar Set Screw (2 places)

Side Bearing

Grease Fitting

Figure 6

26 DR® 10 HP CHIPPER

Image 30

Contents DR→ 10 HP Chipper Safety & Operating Instructions Toll-free phone 1-800-DR-OWNER Table of Contents Iv DR 10 HP Chipper Introducing the DR 10 HP Chipper Conventions used in this manualDR 10 HP Chipper General Safety Rules LabelsDR 10 HP Chipper DR 10 HP Chipper is made in the U.S.A. #091-0062 Protecting Yourself and Those Around You Safety for Children and Pets Safety with Gasoline Powered EnginesGeneral Safety Additional Information and Potential Changes 10 DR 10 HP Chipper Representatives at our toll free number 1-800-DR-OWNER Setting UP Your DR 10 HP ChipperUnpacking Tools and Supplies NeededBe careful when cutting the banding Attaching the Chipper Hopper Check the Tire PressureTool Needed Adding the Engine Oil and Gasoline CapacitiesFront 16 DR 10 HP Chipper Operating Your DR 10 HP Chipper Before Starting the EngineOperation Notes Processing Limbs and Branches Starting and Stopping the Engine Using the Chipper Hopper To Free a Jammed Flywheel DisassembleReassemble Call Toll Free 1-800-DR-OWNER 24 DR 10 HP Chipper Maintaining the DR 10 HP Chipper Regular Maintenance Check ListProcedure EveryGrease Fittings Supplies NeededRemoving and Replacing the Engine Oil Adjusting or Removing and Replacing the Drive Belt 2 WrenchEngine Bolts, Front Belt Tensioner Clutch Drive Belt Removing and Replacing the Chipper Knife Knife SharpeningTools Needed Adjusting the Knife to Wear Plate Gap Wrench or Socket Gap Gauge providedRemoving and Replacing the Clutch DR 10HP Chipper Engine at less than full RPMInstalling a New Clutch Assembly Clutch Removal, Disassembly, and Re-Assembly End of Season and Storage 38 DR 10 HP Chipper Troubleshooting Troubleshooting TableEngine smokes Flywheel will not turn Drive Belt burns Chipper Knife is hitting the Wear Plate Parts LISTS, Schematic Diagrams and Warranty Parts List DR 10 HP ChipperPart# Description Schematic DR 10 HP Chipper Parts List Chipper Assembly Not IllustratedSchematic Chipper Assembly 46 DR 10 HP Chipper DR 10WarrantyHP Chipper Daily Checklist for the DR 10 HP Chipper