Country Home Products 10 HP manual Installing a New Clutch Assembly, Tools and Supplies Needed

Page 39

Installing a New Clutch Assembly

If you have problems with the Clutch, we recommend replacing your Clutch as a complete assembly.

Tools and Supplies Needed:

•(2) 1/2" Wrench

•9/16" Socket with Extension

•Anti-seize compound

1.Remove the Belt Guard and loosen the Engine Bolts as outlined in Steps 1 and 2 on page 28.

2.After you have loosened the Engine Bolts, remove the Drive Belt and set it aside.

3.Remove the Clutch from the engine crankshaft by removing the 3/8" Bolt, Lock Washer, and Flat Washer and then slide the Clutch Assembly from the crankshaft.

NOTE: The shim behind the Clutch remains on the engine crankshaft.

4.Remove the Key from the keyway in the engine crankshaft and set it aside.

5.Clean the engine crankshaft and remove any burrs, then apply anti-seize compound to the crankshaft.

6.Install the Key in the keyway of the new Clutch hub, align the Key with the slot in the engine crankshaft, and then slide the new Clutch Assembly onto the crankshaft followed by the 3/8" Flat Washer, Lock Washer, and the 3/8" Bolt. Tighten the Bolt securely.

7.Reinstall the Drive Belt and set the Drive Belt tension and alignment per Steps 3 through 5 on page 28.

8.Reinstall the Belt Guard.

CALL TOLL FREE 1-800-DR-OWNER

35

Image 39

Contents DR→ 10 HP Chipper Safety & Operating Instructions Toll-free phone 1-800-DR-OWNER Table of Contents Iv DR 10 HP Chipper Conventions used in this manual Introducing the DR 10 HP ChipperDR 10 HP Chipper Labels General Safety RulesDR 10 HP Chipper DR 10 HP Chipper is made in the U.S.A. #091-0062 Protecting Yourself and Those Around You Safety with Gasoline Powered Engines Safety for Children and PetsGeneral Safety Additional Information and Potential Changes 10 DR 10 HP Chipper Tools and Supplies Needed Setting UP Your DR 10 HP ChipperUnpacking Representatives at our toll free number 1-800-DR-OWNERBe careful when cutting the banding Attaching the Chipper Hopper Check the Tire PressureTool Needed Capacities Adding the Engine Oil and GasolineFront 16 DR 10 HP Chipper Before Starting the Engine Operating Your DR 10 HP ChipperOperation Notes Processing Limbs and Branches Starting and Stopping the Engine Using the Chipper Hopper To Free a Jammed Flywheel DisassembleReassemble Call Toll Free 1-800-DR-OWNER 24 DR 10 HP Chipper Every Regular Maintenance Check ListProcedure Maintaining the DR 10 HP ChipperSupplies Needed Grease FittingsRemoving and Replacing the Engine Oil 2 Wrench Adjusting or Removing and Replacing the Drive BeltEngine Bolts, Front Belt Tensioner Clutch Drive Belt Knife Sharpening Removing and Replacing the Chipper KnifeTools Needed Wrench or Socket Gap Gauge provided Adjusting the Knife to Wear Plate GapDR 10HP Chipper Engine at less than full RPM Removing and Replacing the ClutchInstalling a New Clutch Assembly Clutch Removal, Disassembly, and Re-Assembly End of Season and Storage 38 DR 10 HP Chipper Troubleshooting Table TroubleshootingEngine smokes Flywheel will not turn Drive Belt burns Chipper Knife is hitting the Wear Plate Parts LISTS, Schematic Diagrams and Warranty Parts List DR 10 HP ChipperPart# Description Schematic DR 10 HP Chipper Not Illustrated Parts List Chipper AssemblySchematic Chipper Assembly 46 DR 10 HP Chipper DR 10WarrantyHP Chipper Daily Checklist for the DR 10 HP Chipper