Country Home Products 10 HP Attaching the Chipper Hopper, Check the Tire Pressure, Tool Needed

Page 17

Attaching the Chipper Hopper

Tool Needed:

•(2) 1/2" Wrench or Socket

Tip: Insert a towel or large rag into the opening to keep the Bolts from falling into the Chipper.

1.Attach the Chipper Hopper to the machine using four (4) 5/16"-18 x 3/4" Carriage Bolts, four (4) 5/16" Flat Washers and four (4) 5/16"-18 Nylon Lock Nuts.

NOTE: Be sure to insert the bolts from the inside of the Chipper Hopper so that the threads are sticking out (Figure 1).

2.Install a Flat Washer, then a Lock Nut on each bolt. Initially install the Bolts and Nuts finger tight and then tighten the Nuts one (1) turn using two (2) 1/2" wrenches (Figure 1). Check to see that the Hopper is centered on the Inlet Chute and then tighten the Nuts securely.

3.If you used a towel or rag in the Chipper opening, remove it now.

Bolt (4)

Nut (4)

Chipper Hopper

Access Cover

Washer (4)

Inlet Chute

Chipper Left Side Panel

Figure 1

BE SURE TO FILL THE ENGINE WITH OIL AND GAS BEFORE USE. IF YOU START THE ENGINE WITHOUT OIL IN THE CRANKCASE, THE ENGINE WILL BE DAMAGED BEYOND REPAIR AND WILL NOT BE COVERED UNDER THE WARRANTY. SEE THE NEXT PAGE FOR OIL AND FUEL FILL.

Check the Tire Pressure

There should be 30 psi in each tire.

CALL TOLL FREE 1-800-DR-OWNER

13

Image 17

Contents DR→ 10 HP Chipper Safety & Operating Instructions Toll-free phone 1-800-DR-OWNER Table of Contents Iv DR 10 HP Chipper Conventions used in this manual Introducing the DR 10 HP ChipperDR 10 HP Chipper Labels General Safety RulesDR 10 HP Chipper DR 10 HP Chipper is made in the U.S.A. #091-0062 Protecting Yourself and Those Around You Safety with Gasoline Powered Engines Safety for Children and PetsGeneral Safety Additional Information and Potential Changes 10 DR 10 HP Chipper Unpacking Setting UP Your DR 10 HP ChipperRepresentatives at our toll free number 1-800-DR-OWNER Tools and Supplies NeededBe careful when cutting the banding Tool Needed Attaching the Chipper HopperCheck the Tire Pressure Capacities Adding the Engine Oil and GasolineFront 16 DR 10 HP Chipper Before Starting the Engine Operating Your DR 10 HP ChipperOperation Notes Processing Limbs and Branches Starting and Stopping the Engine Using the Chipper Hopper Reassemble To Free a Jammed FlywheelDisassemble Call Toll Free 1-800-DR-OWNER 24 DR 10 HP Chipper Procedure Regular Maintenance Check ListMaintaining the DR 10 HP Chipper EverySupplies Needed Grease FittingsRemoving and Replacing the Engine Oil 2 Wrench Adjusting or Removing and Replacing the Drive BeltEngine Bolts, Front Belt Tensioner Clutch Drive Belt Knife Sharpening Removing and Replacing the Chipper KnifeTools Needed Wrench or Socket Gap Gauge provided Adjusting the Knife to Wear Plate GapDR 10HP Chipper Engine at less than full RPM Removing and Replacing the ClutchInstalling a New Clutch Assembly Clutch Removal, Disassembly, and Re-Assembly End of Season and Storage 38 DR 10 HP Chipper Troubleshooting Table TroubleshootingEngine smokes Flywheel will not turn Drive Belt burns Chipper Knife is hitting the Wear Plate Part# Description Parts LISTS, Schematic Diagrams and WarrantyParts List DR 10 HP Chipper Schematic DR 10 HP Chipper Not Illustrated Parts List Chipper AssemblySchematic Chipper Assembly 46 DR 10 HP Chipper DR 10WarrantyHP Chipper Daily Checklist for the DR 10 HP Chipper