Country Home Products 10 HP manual To Free a Jammed Flywheel, Disassemble, Reassemble

Page 26

To Free a Jammed Flywheel

BEFORE PERFORMING ANY MAINTENANCE PROCEDURE OR INSPECTION, STOP THE ENGINE, WAIT FIVE

(5)MINUTES TO ALLOW ALL MOVING PARTS TO COME TO A COMPLETE STOP AND COOL. DISCONNECT THE SPARK PLUG WIRE, KEEPING IT AWAY FROM THE SPARK PLUG.

Tool Needed:

(2)1/2" Wrench or Socket

Disassemble:

1.Remove any material left in the Chipper Hopper and then remove the Deflector by removing the two (2) 5/16" x 4" Bolts (Figure 5).

NEVER PRY AGAINST THE SCROLL WHEN REMOVING THE DEFLECTOR, OR AT ANY OTHER TIME. THIS WILL CAUSE DAMAGE TO THE MACHINE.

2.Check to see if the Deflector or Discharge opening is clogged. If it is, clear it with a branch.

3.With a wooden stick, loosen and remove any material left in the Chipping Chamber.

Reassemble:

1.Hold the Deflector (Figure 5) in place at the Discharge opening of the Chipper.

2.Place a 5/16" Flat Washer on a 5/16"-18 x 4" Bolt and then slide the Bolt through both the top two

(2) holes of the Chipper body and the Deflector.

NOTE: Be certain that the Bolt attaching the Deflector to the Chipper passes through the pipe (tube) welded to the Scroll (Figure 5).

5/16" Lock Nut (2)

Deflector	5/16" Bolt (2)

Scroll

5/16" Flat Washer (4)

Figure 5

22 DR® 10 HP CHIPPER

Image 26

Contents DR→ 10 HP Chipper Safety & Operating Instructions Toll-free phone 1-800-DR-OWNER Table of Contents Iv DR 10 HP Chipper Introducing the DR 10 HP Chipper Conventions used in this manualDR 10 HP Chipper General Safety Rules LabelsDR 10 HP Chipper DR 10 HP Chipper is made in the U.S.A. #091-0062 Protecting Yourself and Those Around You Safety for Children and Pets Safety with Gasoline Powered EnginesGeneral Safety Additional Information and Potential Changes 10 DR 10 HP Chipper Representatives at our toll free number 1-800-DR-OWNER Setting UP Your DR 10 HP ChipperUnpacking Tools and Supplies NeededBe careful when cutting the banding Tool Needed Attaching the Chipper HopperCheck the Tire Pressure Adding the Engine Oil and Gasoline CapacitiesFront 16 DR 10 HP Chipper Operating Your DR 10 HP Chipper Before Starting the EngineOperation Notes Processing Limbs and Branches Starting and Stopping the Engine Using the Chipper Hopper Reassemble To Free a Jammed FlywheelDisassemble Call Toll Free 1-800-DR-OWNER 24 DR 10 HP Chipper Maintaining the DR 10 HP Chipper Regular Maintenance Check ListProcedure EveryGrease Fittings Supplies NeededRemoving and Replacing the Engine Oil Adjusting or Removing and Replacing the Drive Belt 2 WrenchEngine Bolts, Front Belt Tensioner Clutch Drive Belt Removing and Replacing the Chipper Knife Knife SharpeningTools Needed Adjusting the Knife to Wear Plate Gap Wrench or Socket Gap Gauge providedRemoving and Replacing the Clutch DR 10HP Chipper Engine at less than full RPMInstalling a New Clutch Assembly Clutch Removal, Disassembly, and Re-Assembly End of Season and Storage 38 DR 10 HP Chipper Troubleshooting Troubleshooting TableEngine smokes Flywheel will not turn Drive Belt burns Chipper Knife is hitting the Wear Plate Part# Description Parts LISTS, Schematic Diagrams and WarrantyParts List DR 10 HP Chipper Schematic DR 10 HP Chipper Parts List Chipper Assembly Not IllustratedSchematic Chipper Assembly 46 DR 10 HP Chipper DR 10WarrantyHP Chipper Daily Checklist for the DR 10 HP Chipper