Black & Decker 479970-00, LP1000 instruction manual Operation

Page 11

479970-00 LP1000 9/14/05 1:00 PM Page 11

Pull the chain bar and chain back, engaging it in the groove in the chain bar and then over the sprocket (14) positioning teeth in the correct position on the sprocket.

-Replace the chain access cover (12) and retention nuts (11) tightening securely.

Operation

Never operate a chain saw that is damaged or improperly adjusted or that is not completely and securely assembled. Be sure that the saw chain stops moving when the power control system triggers are released. Never adjust the guide bar or saw chain when the engine is operating.

WARNING: Let the tool work at its own pace. Do not overload.

-Carry out regular cleaning of the unit as described in the maintenance section and in particular cleaning inside the chain access cover.

-The lower guard (7) and top jaw (6) are designed to close when one of the handles is released or when the piece of branch being cut has been cut. If this does not occur, discontinue use of the tool and remove the power cord. Check if any debris is blocking movement. To help in this process it may be necessary to remove chain access cover(12). If on assembly the problem is still present take the unit to a service center.

Extension Cord (fig. E)

To reduce the risk of disconnection of appliance cord from the extension cord during operation make a knot as shown in Figure E on page 8.

NOTE: Always keep the cord away from the cutting area and position the cord so that it will not be caught on branches, and other material, during cutting.

Oiling (fig. F)

A high quality bar and chain oil or SAE30 weight motor oil should be used for chain and bar lubrication. The use of a vegetable based bar and chain oil is recommended when pruning trees. Never use waste oil or very thick oil. These may damage your chain saw.

-Before first use and every ten minutes of use you must oil the product with the recommended chain oil. Open the oiling cover (10) and insert the bottle into the oil filling hole (15) apply pressure to the bottle once to dispense oil.

-This should be adequate for about 10 minutes of cutting depending upon cutting speed and type of wood.

-The hole feeds the oil through to the chain onto the chain bar and an excessive amount of oil applied to the unit could mean the oil drips from the unit around the jaw area. This is normal and is nothing to be concerned about.

Switching on and off (fig. G)

For your safety, this tool is equipped with a double switching system. This system prevents starting the tool inadvertently.

A chain saw is intended for two-handed use. Serious injury to the operator, helpers, and/or bystanders can result from one-handed operation.

Switching on

Ensure a firm grip on the handles and then squeeze both switch actuators to switch the unit on.

Note: Both switches must be activated for the product to be used. Do not force the tool - allow it to do the work. It will do a better and safer job at the speed for which it is designed. Excessive force will stretch the chain.

If the saw chain or bar becomes jammed:

-Switch the tool off.

-Disconnect the tool from the power supply.

-Open the cut with wedges to relieve the strain on the guide bar. Do not try to wrench the saw free. Start a fresh cut.

Trimming branches

-Make sure the tool is running at full speed before making a cut.

-Hold the tool firmly in place to avoid possible bouncing or sideways movement of the tool.

-Guide the tool using light pressure.

-Always cut down from the top. This way you will avoid pinching the saw chain.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents 0 0 5 4 4 6 9 8 Intended use General Safety Rules479970-00 LP1000 9/14/05 100 PM Distance is at risk from being struck by the falling branch Additional safety instructions for the AlligatorTM LopperKickback Safety Features Double Insulation Extension CordPolarized Plugs Chain SAW Names and Terms 479970-00 LP1000 14/05 100 PM Overview ContentsAssembling the chain bar and chain figs. C&D Checking and adjusting the chain tension fig. aReplacing the chain and chain bar Removing the saw chain & chain bar figs. a & BOperation Full Two-Year Home Use Warranty Troubleshooting Section Mode D’EMPLOI Règles de sécurité générales Utilisation prévueEncercler les poignées avec les pouces et doigts 479970-00 LP1000 9/14/05 100 PM Directives de sécurité concernant l’effet de rebond Double isolation RallongeTerminologie ET Nomenclature Relatives À L’ÉBRANCHEUR Fiches polariséesRéglage de la tension de la chaîne fig. a ContenuAperçu général Assemblage de la chaîne et du guide chaîne fig. C & D Remplacement de la chaîne et du guide chaîneEnlever la chaîne et le guide chaîne fig. a & B Allumer et éteindre l’outil fig. G FonctionnementRallonge Fig. E Lubrification Fig. FInformation sur les réparations AccessoiresSection de dépannage Problème Cause possible Solution possibleManual DE Instrucciones Normas generales de seguridad Uso previstoLimpios y libres de aceite y grasas 479970-00 LP1000 9/14/05 100 PM Características de seguridad durante el retroceso Cable prolongador Enchufes polarizados Doble aislamientoPreparación de la Podadora AlligatorTM para su utilización ContenidoDescripción general Reemplazo de la cadena y de la barra de la cadena Ajuste de tensión de la cadena Figura aVerificación y ajuste de la tensión de la cadena Figura a Lubricación Figura F OperaciónCable prolongador Figura E Mantenimiento Encendido y apagado Figura GEncendido Recorte de ramasAlmacenamiento AccesoriosInformación de servicio TransporteProblema Causa posible Solución posible Sección de detección de problemasEspecificaciones 479970-00 LP1000 9/14/05 100 PM

479970-00, LP1000 specifications

The Black & Decker 479970-00, LP1000 model is a versatile and innovative power tool that brings convenience and efficiency to various tasks around the home and workplace. This product is designed for both professionals and DIY enthusiasts, showcasing a blend of functionality, reliability, and user-friendly features.

One of the key highlights of the LP1000 is its powerful motor, which delivers impressive performance for a wide range of applications. With robust power output, users can tackle demanding tasks with ease, whether it’s cutting through tough materials, drilling holes, or driving screws. The high-efficiency motor ensures that users experience consistent speeds and torque, making it an ideal choice for heavy-duty projects.

The LP1000 is equipped with an ergonomic design that enhances user comfort during extended use. Its lightweight construction allows for easy maneuverability, reducing fatigue and increasing overall productivity. The soft-grip handle provides an additional layer of comfort, allowing users to maintain a firm hold even during intricate tasks. This focus on user experience is a testament to Black & Decker’s commitment to providing tools that cater to the needs of both seasoned professionals and hobbyists.

Another significant feature of the LP1000 is its advanced safety technology. It includes a built-in safety switch that prevents accidental startups, ensuring that users can operate the tool without worrying about unintended activation. This is particularly important when working in tight spaces or on delicate projects where precision is crucial.

The LP1000 also stands out due to its adaptability. It comes with a variety of interchangeable attachments, allowing users to customize the tool for specific tasks. Whether users need to drill, sand, or cut, this model can be easily transformed to meet their needs, making it a truly multifunctional tool.

Moreover, the LP1000 is designed with durability in mind. Constructed from high-quality materials, it offers resilience against wear and tear, ensuring longevity even in demanding working conditions. This reliability makes it a worthy investment for anyone looking to enhance their toolkit.

In summary, the Black & Decker 479970-00, LP1000 is a powerful, efficient, and user-friendly tool. With its versatile features, safety innovations, and ergonomic design, it stands out as an essential piece of equipment for anyone tackling home improvement projects or professional tasks. Whether you’re a seasoned professional or a novice DIYer, this tool is engineered to enhance your productivity and deliver outstanding results.
Top Page Image Contents