Ariens 911194 warranty Check Wheel Drive Control, Check Grass BAG, Clean Unit, Check Engine OIL

Page 18

CHECK WHEEL DRIVE CONTROL

(Self-Propelled Models)

The unit must stop quickly and completely when the control is released. Adjust or repair

if necessary. See WHEEL DRIVE CONTROL ADJUSTMENT on page 22.

CHECK GRASS BAG

Check grass bag frequently for wear or deterioration. Replace worn or damaged bag with an Ariens original equipment replacement bag only.

CLEAN UNIT

Before each use clean unit, muffler and engine surfaces of debris, oil or fuel spills to ensure proper cooling and prevent fires.

CHECK ENGINE OIL

IMPORTANT: Maintain proper oil level at all times or engine damage will result.

Check the level of the engine crankcase oil before each use.

Make sure engine is level when checking oil. See engine manual for instructions.

CHECK MOWER BLADE

See Figure 11.

Check blade mounting: blade must be secure and bolt torqued to 37.5 – 50 lbf-ft (51 –

68 N•m) (bolt should fully compress lock washer).Check blade for nicks and dull cutting edges. Sharpen if necessary.

Check blade for rounded or broken ends, thinned metal or other damage. Replace if necessary.

NOTE: Blades should be sharpened and balanced professionally. Contact your Ariens Dealer.

To remove blade:

1.Stop engine, wait for all moving parts to stop, and disconnect spark plug wire.

2.Block blade to prevent rotation.

3.Remove bolt, lock washer, flat washer and blade from shaft.

To install blade:

1.Replace blade, flat washer, lock washer and bolt on shaft.

2.Torque bolt to 37.5 – 50 lbf-ft (51 –

68 N•m) (bolt should fully compress lock washer).

3.Connect spark plug wire.

Sharpen the Mower Blades

CAUTION: DO NOT sharpen mower blades while on unit. An imbalanced mower blade will cause excessive vibration and eventual damage to unit. Check mower blade balance before reinstalling blades.

NEVER weld or straighten bent blades.

1.Remove mower blade from unit. Discard mower blade if:

•More than 1/2 in. (1.27 cm) of metal is removed.Air lifts become eroded.

•Blade is bent or broken.

2.Sharpen mower blade by removing an equal amount of material from each end of mower blade. DO NOT change angle of cutting edge or round the corner of the mower blade.

DO NOT Sharpen to This Pattern

 

1

2

 

3

 

 

DISCARD If More Than

 

1/2 in. (1.27 cm)

2

4

3

OT0792

 

Sharpen to This Pattern

 

1.

Square Corner

 

2.

Cutting Edge

 

3.

Air Lift

 

4.

Air Lift Erosion

 

 

Figure 11

 

GB - 18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Walk Behind Lawn Mower Table of Contents IntroductionUnauthorized Replacement Parts Dealer Delivery Product RegistrationDisclaimer Notations SafetySafety Alerts Practices and LawsSafety Decals Locations Safety RulesEmission Control System Wear appropriate hearing protection Emission Control System Certification Label Page Assembly Carton ContentsAssembly Controls and Features Controls and Features Cutting Height AdjustmentOperation Optional Controls Speed Control self-propelled models Wheel Drive Control self-propelled modelsSwivel Wheel Lock Fuel Stabilizer Filling the Fuel Tank GasolineMower SET-UP To add fuel to fuel tankTo Side Discharge To BagGrass Bag Removal To MulchEmergency Stopping Starting and Shut OFFMaintenance Schedule MaintenanceMaintenance Schedule Check ENGINE/BLADE ControlCheck Grass BAG Clean UnitCheck Wheel Drive Control Check Engine OILCheck Fasteners Check AIR CleanerCheck Drive Belt Change Engine OILDrive Belt Replacement Service and AdjustmentsService Position Handlebar HeightNo slack Wheel Drive Control Adjustment To increase the gapSpeed Control Bell Crank To decrease the gapStorage Troubleshooting Service Parts AccessoriesSpecifications 911193 911194 911170 911192Consumer Mowing Equipment Limited Warranty Limitation of Remedy and Damages Your Warranty Rights and Obligations Evaporative Emission Warranty Parts List DisclaimerAriens West Ryan Street Brillion, WI Fax Walk Behind Lawn Mower Manuel DU Moteur Table DES MatièresLE Manuel Entretien ET Pièces DE RechangeEnregistrement DU Produit Pièces DE Rechange NON HomologuéesLimitation DE Responsabilité Remarques SécuritéConsignes DE Sécurité Usages ET LoisAutocollants DE Sécurité ET Emplacements Système DE Contrôle DES ÉmissionsPage Page Page Page Montage ContenuMontage Commandes ET Fonctions Commandes ET Fonctions FonctionnementRéglage DE LA Hauteur DE Coupe Modèles standard Modèles avec roues pivotantesCommande d’entraînement modèles auto-tractés Commandes EN OptionCommande de vitesse modèles auto- tractés Poire d’amorçage 911192, 193Remplissage DU Réservoir DE Carburant Réglage DE LA TondeuseStabilisateur d’essence Evacuation latérale Pour ensacherDépose du sac à herbe PaillisArrêt D’URGENCE Mise EN Marche ET ArrêtPériodicité DE ’ENTRETIEN Vérification DE LA Commande MOTEUR/LAMEEntretien Périodicité DE L’ENTRETIENVérification DE L’HUILE Moteur Vérification DU SAC a HerbeNettoyage DE LA Machine Vérifier LA LameVidange DE L’HUILE Moteur Vérification DE LA VisserieVérification DU Filtre À AIR Graissage GénéralPosition Pour L’ENTRETIEN Entretien ET RéglagesVérification DES Bougies Prudence RemplacerRemplacement DE LA Courroie D’ENTRAÎNEMENT Hauteur DU GuidonModèles auto-tractés Tendu Auto-tractésLevier Coudé DE Commande DE Vitesse modèles auto-tractés Pour réduire l’espaceSac à herbe RemisageNettoyage MoteurDépannage Ne s’enclenche La commande’entraînement Pas modèlesAccessoires Pièces DE RechangeSpécifications Extensions spéciales Limitations DE Recours ET DE Dommages VOS Droits ET Obligations Dans LE Cadre DE LA Garantie Déni de responsabilité Ariens West Ryan Street Brillion, WI Fax

911194 specifications

The Ariens 911194 is a powerful and efficient snow blower designed for residential use, specifically engineered to handle heavy snowfall with ease. As part of the Ariens brand, known for its reliable and durable outdoor power equipment, the 911194 lives up to high expectations, showcasing advanced technology and solid construction.

One of the standout features of the Ariens 911194 is its 24-inch clearing width, allowing users to quickly clear large areas of snow in a single pass. This makes the machine particularly effective for driveways, sidewalks, and large patios. The snow blower is equipped with a 208cc, 4-cycle engine, which provides ample power and robust performance. Its reliable engine starts smoothly in cold weather, ensuring that users can tackle any winter storm without delay.

The Ariens 911194 also features an innovative, adjustable chute that allows for precise control of snow direction. Operators can rotate the chute up to 200 degrees, making it easier to throw snow precisely where it needs to go. This feature is enhanced by a remote deflector that allows users to change the height of the snow stream without stopping the machine, increasing efficiency during operation.

Another key characteristic of the Ariens 911194 is its 6-speed forward and 2-speed reverse transmission. This variability enables users to easily navigate different snow conditions and terrains, ensuring optimal control and maneuverability. The heavy-duty construction includes a durable steel auger and housing, designed to withstand the harshest winter conditions and provide long-lasting performance.

Additionally, the snow blower comes with large, all-terrain tires, which provide excellent traction on icy or uneven surfaces. This ensures that users can operate the machine confidently, regardless of the conditions. Ergonomically designed handles and controls also enhance user comfort, making extended use more manageable.

In conclusion, the Ariens 911194 is a well-rounded snow blower that combines power, efficiency, and user-friendly features. Its robust engine, versatile controls, and durable construction make it an excellent choice for homeowners looking to manage winter's challenges effectively. With the technology and features included, it stands as a reliable investment for maintaining clear and safe outdoor spaces during snowy months.
Top Page Image Contents