Ariens 911194 Service and Adjustments, Service Position, Handlebar Height, Drive Belt Replacement

Page 20

SERVICE AND ADJUSTMENTS

CAUTION: AVOID INJURY. Read and understand the entire Safety section before proceeding.

SERVICE POSITION

Put unit into service position for easy access to underneath the deck.

CAUTION: Avoid fuel spills. Follow steps below to help prevent fuel spills. If fuel leaks into air cleaner, replace air cleaner. ALWAYS clean up any spilled fuel.

1.Place unit on a flat, level surface.

2.Disconnect spark plug wire.

3.Remove fuel cap, place a piece of plastic bag over the opening and tighten cap securely.

4.Tip unit onto right side. Make sure unit is secure and will not tip over.

IMPORTANT: Remove plastic from fuel cap after unit is upright and service is complete.

HANDLEBAR HEIGHT

To adjust (Figure 14):

1.Place a hole at the bottom of the braces over the pins on the bracket.

NOTE: To fold handlebars flat for storage, pull the speed control rod (if equipped) all the way back, disconnect braces from support bracket, and fold handlebar forward. Do not bend speed control rod.

Hole

Pin

OM1800

Figure 14

DRIVE BELT REPLACEMENT

(Self-Propelled Models)

To remove drive belt:

1.Disconnect spark plug wire.

2.Set the right rear wheel to its lowest cutting height, and the left rear wheel to the third cutting height. This position provides clearance between friction disc and drive sheave.

3.Remove belt from the idler, then the drive sheave, and finally, the engine pulley (Figure 15).

4.Pull belt through opening under mower pan and over blade.

5.Make sure the idler pulley turns and the idler arm moves freely.

6.Reinstall drive belt in reverse order.

IMPORTANT: Be sure the belt seats in sheave and pulley grooves with the idler touching the back (flat) side of belt.

7.Adjust rear wheels to the same cutting height.

5

 

 

6

 

 

 

 

 

 

1

 

 

 

2

4

 

 

3

 

 

 

1.

Blade

5. Engine

2.

Idler

 

Pulley

3.

Drive

6.

Bolt, Lock

 

Sheave

 

Washer &

4.

Drive Belt

 

Flat Washer

 

 

Figure 15

 

GB - 20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Walk Behind Lawn Mower Table of Contents IntroductionDisclaimer Unauthorized Replacement Parts Dealer DeliveryProduct Registration Safety Safety AlertsNotations Practices and LawsEmission Control System Safety Decals LocationsSafety Rules Wear appropriate hearing protection Emission Control System Certification Label Page Assembly AssemblyCarton Contents Controls and Features Operation Controls and FeaturesCutting Height Adjustment Optional Controls Swivel Wheel Lock Speed Control self-propelled modelsWheel Drive Control self-propelled models Filling the Fuel Tank Gasoline Mower SET-UPFuel Stabilizer To add fuel to fuel tankTo Bag Grass Bag RemovalTo Side Discharge To MulchEmergency Stopping Starting and Shut OFFMaintenance Maintenance ScheduleMaintenance Schedule Check ENGINE/BLADE ControlClean Unit Check Wheel Drive ControlCheck Grass BAG Check Engine OILCheck AIR Cleaner Check Drive BeltCheck Fasteners Change Engine OILService and Adjustments Service PositionDrive Belt Replacement Handlebar HeightNo slack Wheel Drive Control Adjustment To increase the gapSpeed Control Bell Crank To decrease the gapStorage Troubleshooting Service Parts AccessoriesSpecifications 911193 911194 911170 911192Consumer Mowing Equipment Limited Warranty Limitation of Remedy and Damages Your Warranty Rights and Obligations Evaporative Emission Warranty Parts List DisclaimerAriens West Ryan Street Brillion, WI Fax Walk Behind Lawn Mower Table DES Matières LE ManuelManuel DU Moteur Entretien ET Pièces DE RechangeLimitation DE Responsabilité Enregistrement DU ProduitPièces DE Rechange NON Homologuées Sécurité Consignes DE SécuritéRemarques Usages ET LoisAutocollants DE Sécurité ET Emplacements Système DE Contrôle DES ÉmissionsPage Page Page Page Montage MontageContenu Commandes ET Fonctions Réglage DE LA Hauteur DE Coupe Commandes ET FonctionsFonctionnement Modèles standard Modèles avec roues pivotantesCommandes EN Option Commande de vitesse modèles auto- tractésCommande d’entraînement modèles auto-tractés Poire d’amorçage 911192, 193Stabilisateur d’essence Remplissage DU Réservoir DE CarburantRéglage DE LA Tondeuse Pour ensacher Dépose du sac à herbeEvacuation latérale PaillisArrêt D’URGENCE Mise EN Marche ET ArrêtVérification DE LA Commande MOTEUR/LAME EntretienPériodicité DE ’ENTRETIEN Périodicité DE L’ENTRETIENVérification DU SAC a Herbe Nettoyage DE LA MachineVérification DE L’HUILE Moteur Vérifier LA LameVérification DE LA Visserie Vérification DU Filtre À AIRVidange DE L’HUILE Moteur Graissage GénéralEntretien ET Réglages Vérification DES BougiesPosition Pour L’ENTRETIEN Prudence RemplacerModèles auto-tractés Remplacement DE LA Courroie D’ENTRAÎNEMENTHauteur DU Guidon Tendu Auto-tractésLevier Coudé DE Commande DE Vitesse modèles auto-tractés Pour réduire l’espaceRemisage NettoyageSac à herbe MoteurDépannage La commande ’entraînementNe s’enclenche Pas modèlesAccessoires Pièces DE RechangeSpécifications Extensions spéciales Limitations DE Recours ET DE Dommages VOS Droits ET Obligations Dans LE Cadre DE LA Garantie Déni de responsabilité Ariens West Ryan Street Brillion, WI Fax

911194 specifications

The Ariens 911194 is a powerful and efficient snow blower designed for residential use, specifically engineered to handle heavy snowfall with ease. As part of the Ariens brand, known for its reliable and durable outdoor power equipment, the 911194 lives up to high expectations, showcasing advanced technology and solid construction.

One of the standout features of the Ariens 911194 is its 24-inch clearing width, allowing users to quickly clear large areas of snow in a single pass. This makes the machine particularly effective for driveways, sidewalks, and large patios. The snow blower is equipped with a 208cc, 4-cycle engine, which provides ample power and robust performance. Its reliable engine starts smoothly in cold weather, ensuring that users can tackle any winter storm without delay.

The Ariens 911194 also features an innovative, adjustable chute that allows for precise control of snow direction. Operators can rotate the chute up to 200 degrees, making it easier to throw snow precisely where it needs to go. This feature is enhanced by a remote deflector that allows users to change the height of the snow stream without stopping the machine, increasing efficiency during operation.

Another key characteristic of the Ariens 911194 is its 6-speed forward and 2-speed reverse transmission. This variability enables users to easily navigate different snow conditions and terrains, ensuring optimal control and maneuverability. The heavy-duty construction includes a durable steel auger and housing, designed to withstand the harshest winter conditions and provide long-lasting performance.

Additionally, the snow blower comes with large, all-terrain tires, which provide excellent traction on icy or uneven surfaces. This ensures that users can operate the machine confidently, regardless of the conditions. Ergonomically designed handles and controls also enhance user comfort, making extended use more manageable.

In conclusion, the Ariens 911194 is a well-rounded snow blower that combines power, efficiency, and user-friendly features. Its robust engine, versatile controls, and durable construction make it an excellent choice for homeowners looking to manage winter's challenges effectively. With the technology and features included, it stands as a reliable investment for maintaining clear and safe outdoor spaces during snowy months.
Top Page Image Contents