Alamo 02984405 instruction manual RH Side

Page 37

Frame Installation

5.Install Center Frame Weldment. The Center Frame Weldment has a front and a back side (LH & RH side). The Center frame must be installed with the two openings (See Figure 26) toward the front of the tractor. These openings are to allow for the movement of the swing cylinders when moving the boom to the boom rest position.

IMPORTANT NOTE: When bolting the center frame up to the front and rear frame mounting rails the bolts on the RH turret side must have the bolts installed from the bottom with the bolt heads on bottom under center under frame and the nuts on top (See Figure 27 showing nuts on top). The reason the nuts must be on top is so the bolts will not hit the swing cylinders when the turret assembly has been mounted. The Bolts that are used to mount center frame are not the same lentgh. The 8 bolts for the rear fame bracts (bolts that face the rear of the tractor) will be 3/4" X 3-1/2" long. The other twelve bolts will be 3/4" X 2-1/4" long. All 20 Bolts that at are used to mount center frame MUST have hardened flat washers install on both sides, one under Bolt Head and one under Nut (See Figure 26 & 27)

Using floor jacks (or Fork lift) position the center frame weldment up under the tractor (See Figure 27). The center frame weldment will bolt to the front and rear mounting rails on both sides. Make Certain to use hardened flatwashers on all 3/4" and 20 mm bolts, when using nut on bolts it will need two hardened washers, one on each side (See Figure 27) . Double check the frame mounting bolt tightness.

RH Side

Rear Top Mounting Holes use 3/4" X 2-1/

of Tractor

4" bolts in these 4 places

Front Mounting

 

Holes use 3/4" X

Rear of

2-1/4" bolts in

Tractor

these 8 places

 

Install with these openings to front

of tractor

Front of

LH Side of

Tractor

Tractor

 

Rear Mounting Holes use 3/4" X

Center Section Under Mount Frame Wldmnt

 

3-1/2" bolts in these 8 places

Rear View

 

Figure 26

6.Install Boom Rest Weldment. The boom rest weldment for the 24 foot boom and the 30 ft. boom are not the same (See Figure 29). The boom rest weldment bolts to the RH Side on the Rear Frame mount weldment behind the tractor axle weldment (See Figure 30). It is recommended that this be installed using an overhead hoist and supported by the hoist until boom rest and support brace (See Figure 28 & 30) are completely installed. The Boom Rest Support also serves as the top axle strap for the RH Axle mount (See Figure 30).

Axtreme Boom (Asy.

Man) 07/06

 

 

 

 

© 2006 Alamo Group Inc.

Section 4 - 9

 

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Assembly Manual Page Page To the OWNER/OPERATOR/DEALER Axtreme Boom General Assembly 02-06 Rev Introduction Index Page Axtreme Boom Safety Section LEA EL Instructivo SG-23 Safety Section Safety Section Axtreme Boom Pump Specifications Specifications Axtreme BoomRotary Head Torque Specification Fifty Inch 50 Cutting Head SpecificationsSixty Inch 60 Rotary Mower Head Mechanical Remote Cable Controled Valve Standard Valve Sections Function Controled Valve OptionalDash Nominal Cyl Torque Size In. lbs Ft .lbs Hose End Fitting Torque SpecificationTractor Preperations General Information General Information / Installation RequirementsLeveling Tractor Replacement Oil Filter Tractor Preparation Cleaning Boom and mower componets electronics Tractor, Area CleanlinessDo not Weld On This Unit During or After Installation Axtreme Boom Asy. Man 07/06 Axtreme Boom Asy. Man 07/06 Battery Holder Relocation Exhaust / Muffler Relocation Exhaust/Muffler Relocation Fuel Tank Replacement Rear Bracket Bolt Front Under Mount Frame Asy Frame Installation Alamo Group Inc RH Side LH side of tractor Upper Axle strap Counter Weight Installation Turret Assembly Installation Axtreme Boom Asy Man 07/06 Boom Swing Adjustment Adjust Boom Swing StopTurret Assembly as seen from the bottom Axtreme Boom Asy. Man 07/06 Wheel Weight Installation Fill Left Rear Wheel with Liquid Rear Wheel Counter WeightInstalling Wheel Weight Axtreme Boom Asy. Man /06 Typical Pump Driveline Hyd Assembly instructions Pump Driveline Hose Information Pump Driveline Hose RemovalPump Pump Driveline Hose InstallationPump Driveline Hose Installation Splined Hose Installation Motor Control Valve Block Cylinder Diverter Valve Block Used with Swivel Head Option OnlyReturn Oil Cooler with Fan Hyd Schematic Mechanical Operated Std Hyd Schematic Electrically Controlled Opt Axtreme Boom Asy Man 07/06 Boom & Head Installation With Hyd Connections Boom / Head Installation Turret End Boom Boom Mounting Pin Hole Motor Circuit Hoses to Boom Connections Listed as reference Motor Tank Return Orange Tie Blue Tie Red Tie Hydraulic Hose Connections Diverter Valve Controled Valve Motor Return Connecting Hose To Head Hyd Schematic Electrically Controlled Opt Alamo Group Inc Remote Valve Cable Installation Common Problems On OFF Switch InstallationWire Harness Cable Controled Valve Cylinder Control Valve Cables To Valve Spools Valve Remote Cable ControlsRemote Cable Operation and Installation Door/Swivel Tilt Dipper Lift Swing Dipper Alamo Industrial Black Wiring Tractor with Remote Cable Cylinder Control Valve Hyd Schematic Mechanical Operated Std 2345672345 22 6 Remote Cable Controled Valve StandardAxtreme Boom Joystick Optional Joystick MountingJoystick Resister Wiring Harness used With Joystick Valve Controls Only Joystick Installation Ing instructions Make certain these wires have Starter Installing Wire Harness To Valve Plug Function 2345678901234567 Lift Orange/ White Fill Hydraulic Tank Start Up Instructions Fill Hydraulic Tank with Oil Fill Hydraulic TankSuction Hose Axtreme Boom Asy. Man /06 PRE-DELIVERY Inspection Checklist Frame and Boom Saftey EquipmentHydraulic System Rotary Mower HeadTractor Mower Operation Inspection Flail Mower HeadPost-Operation Inspection Axtreme Boom Asy. Manl 07/06 Page Axtreme Boom Assembly Manual

02984405 specifications

Alamo 02984405 is a significant model in the landscape of modern transportation, particularly known for its robust performance and advanced technology integration. This vehicle is engineered to excel in a variety of environments, from urban settings to rugged terrains, making it a versatile choice for users with diverse needs.

One of the standout features of Alamo 02984405 is its powerful engine, which is designed to deliver impressive horsepower and torque. This allows for dynamic acceleration and remarkable handling, ensuring that drivers can navigate both city streets and off-road paths with ease. Coupled with advanced suspension systems, the vehicle provides a smooth ride while maintaining stability even on challenging surfaces.

In terms of technology, Alamo 02984405 is equipped with an intuitive infotainment system that offers seamless connectivity with smartphones and other devices. The system supports various apps for navigation, entertainment, and communication, ensuring that occupants remain connected while on the move. Additionally, features such as Bluetooth, USB ports, and wireless charging pads enhance convenience and usability.

Safety is a paramount concern in the design of Alamo 02984405. The vehicle integrates multiple advanced safety features, including adaptive cruise control, lane-keeping assist, and automatic emergency braking. These technologies work together to provide a safer driving experience, actively assisting the driver in avoiding potential hazards and accidents.

Moreover, Alamo 02984405 embodies a commitment to sustainability. It incorporates eco-friendly technologies that aim to reduce fuel consumption and emissions. This includes engine efficiency improvements and options for hybrid or electric variations, catering to environmentally conscious consumers.

The interior of Alamo 02984405 is designed with comfort and functionality in mind. It boasts spacious seating and versatile cargo solutions that adapt to different transport needs. High-quality materials are used throughout the cabin, creating a premium feel while ensuring durability.

Lastly, the exterior design of Alamo 02984405 is both stylish and practical, featuring aerodynamic lines that enhance fuel efficiency while asserting a modern aesthetic. Available in various colors and finishes, this vehicle offers personalization options that appeal to a wide range of customers.

In summary, Alamo 02984405 is a well-rounded vehicle that combines performance, technology, safety, and design. With its focus on user experience and environmental responsibility, it stands out as a reliable choice in the competitive automotive market.
Top Page Image Contents