Alamo 02984405 instruction manual Adjust Boom Swing Stop, Boom Swing Adjustment

Page 42
Swing Cylinders

Adjust Boom Swing Stop

CAUTION ! You MUST READ and UNDERSTAND this section as it is critcal BEFORE

attempting to put boom rest position the first time. FAILURE TO PERFORM THIS ADJUSTMENT could cause damage to the cab of the tractor.

Boom Swing Adjustment:

1.Boom Swing Stop Location. The boom Stop adjust- ment cannot be seen from the top of the turret assembly (See Figure 41). If the bottom cover plate (See Item 42) is not already removed it will need to be, it is bolted on from the under side of the turret assembly. From the under side you will see the swing cylinders and cylinder pivot mounts (See Figure 43).

2.The Swing Stop Lug which is part of the Turret Cylinder Link Weldment (See Figure 45). On the side toward the rear there will be a lug with a bolt and locking nut in it (See Figure 45). Loosen the bolt and locking nut, turn the bolt outward.

3.Swinging Boom, DO NOT Swing Boom until the boom has been run with it sticking out away from tractor and all electronic control adjustments have been done. The boom must be working smoothly. Slowly (with low engine RPM) with some one guiding you swing boom inward toward cab until the boom rest lug is aligned with the boom rest pin (See Figure 44). Set boom securely down over pin.

4.Final Swing Stop Adjustment. Unscrew the stop bolt (See Figure 45) until the head is against the swing stop lug of the turret cylinder link weldment (See Figure 45). Hold the bolt so it won't turn tighten the locking nut down against the turret stop swing lug. Recheck to make certain the boom will not hit the cab of the tractor. It will stop at the turret stop lug when properly adjusted. This may have to be

Turret

Assembly

Figure 41

Bottom

Turret

Cover

Figure 42

adjusted more than once, NEVER allow unit to be run if Boom will hit the cab, this will damage cab.

Boom

Rest

Lug

Boom

Rest

Pin

Figure 43

Figure 44

Axtreme Boom (Asy. Man) 07/06

© 2006 Alamo Group Inc.

Section 4 - 14

Page 41 Page 43
Image 42
Page 41 Page 43
Contents Assembly Manual Page Page To the OWNER/OPERATOR/DEALER Axtreme Boom General Assembly 02-06 Rev Introduction Index Page Axtreme Boom Safety Section LEA EL Instructivo SG-23 Safety Section Safety Section Axtreme Boom Specifications Axtreme Boom Pump SpecificationsFifty Inch 50 Cutting Head Specifications Rotary Head Torque SpecificationSixty Inch 60 Rotary Mower Head Mechanical Remote Cable Controled Valve Standard Controled Valve Optional Valve Sections FunctionHose End Fitting Torque Specification Dash Nominal Cyl Torque Size In. lbs Ft .lbsTractor Preperations General Information / Installation Requirements General InformationLeveling Tractor Replacement Oil Filter Tractor Preparation Tractor, Area Cleanliness Cleaning Boom and mower componets electronicsDo not Weld On This Unit During or After Installation Axtreme Boom Asy. Man 07/06 Axtreme Boom Asy. Man 07/06 Battery Holder Relocation Exhaust / Muffler Relocation Exhaust/Muffler Relocation Fuel Tank Replacement Rear Bracket Bolt Front Under Mount Frame Asy Frame Installation Alamo Group Inc RH Side LH side of tractor Upper Axle strap Counter Weight Installation Turret Assembly Installation Axtreme Boom Asy Man 07/06 Adjust Boom Swing Stop Boom Swing AdjustmentTurret Assembly as seen from the bottom Axtreme Boom Asy. Man 07/06 Wheel Weight Installation Rear Wheel Counter Weight Fill Left Rear Wheel with LiquidInstalling Wheel Weight Axtreme Boom Asy. Man /06 Typical Pump Driveline Hyd Assembly instructions Pump Driveline Hose Removal Pump Driveline Hose InformationPump Driveline Hose Installation PumpPump Driveline Hose Installation Splined Hose Installation Motor Control Valve Block Used with Swivel Head Option Only Cylinder Diverter Valve BlockReturn Oil Cooler with Fan Hyd Schematic Mechanical Operated Std Hyd Schematic Electrically Controlled Opt Axtreme Boom Asy Man 07/06 Boom & Head Installation With Hyd Connections Boom / Head Installation Turret End Boom Boom Mounting Pin Hole Motor Circuit Hoses to Boom Connections Listed as reference Motor Tank Return Orange Tie Blue Tie Red Tie Hydraulic Hose Connections Diverter Valve Controled Valve Motor Return Connecting Hose To Head Hyd Schematic Electrically Controlled Opt Alamo Group Inc Remote Valve Cable Installation On OFF Switch Installation Common ProblemsWire Harness Cable Controled Valve Valve Remote Cable Controls Cylinder Control Valve Cables To Valve SpoolsRemote Cable Operation and Installation Door/Swivel Tilt Dipper Lift Swing Dipper Alamo Industrial Black Wiring Tractor with Remote Cable Cylinder Control Valve Hyd Schematic Mechanical Operated Std Remote Cable Controled Valve Standard 2345672345 22 6Axtreme Boom Joystick Mounting Joystick OptionalJoystick Resister Wiring Harness used With Joystick Valve Controls Only Joystick Installation Ing instructions Make certain these wires have Starter Installing Wire Harness To Valve Plug Function 2345678901234567 Lift Orange/ White Fill Hydraulic Tank Start Up Instructions Fill Hydraulic Tank Fill Hydraulic Tank with OilSuction Hose Axtreme Boom Asy. Man /06 PRE-DELIVERY Inspection Checklist Hydraulic System Saftey EquipmentFrame and Boom Rotary Mower HeadFlail Mower Head Tractor Mower Operation InspectionPost-Operation Inspection Axtreme Boom Asy. Manl 07/06 Page Axtreme Boom Assembly Manual

02984405 specifications

Alamo 02984405 is a significant model in the landscape of modern transportation, particularly known for its robust performance and advanced technology integration. This vehicle is engineered to excel in a variety of environments, from urban settings to rugged terrains, making it a versatile choice for users with diverse needs.

One of the standout features of Alamo 02984405 is its powerful engine, which is designed to deliver impressive horsepower and torque. This allows for dynamic acceleration and remarkable handling, ensuring that drivers can navigate both city streets and off-road paths with ease. Coupled with advanced suspension systems, the vehicle provides a smooth ride while maintaining stability even on challenging surfaces.

In terms of technology, Alamo 02984405 is equipped with an intuitive infotainment system that offers seamless connectivity with smartphones and other devices. The system supports various apps for navigation, entertainment, and communication, ensuring that occupants remain connected while on the move. Additionally, features such as Bluetooth, USB ports, and wireless charging pads enhance convenience and usability.

Safety is a paramount concern in the design of Alamo 02984405. The vehicle integrates multiple advanced safety features, including adaptive cruise control, lane-keeping assist, and automatic emergency braking. These technologies work together to provide a safer driving experience, actively assisting the driver in avoiding potential hazards and accidents.

Moreover, Alamo 02984405 embodies a commitment to sustainability. It incorporates eco-friendly technologies that aim to reduce fuel consumption and emissions. This includes engine efficiency improvements and options for hybrid or electric variations, catering to environmentally conscious consumers.

The interior of Alamo 02984405 is designed with comfort and functionality in mind. It boasts spacious seating and versatile cargo solutions that adapt to different transport needs. High-quality materials are used throughout the cabin, creating a premium feel while ensuring durability.

Lastly, the exterior design of Alamo 02984405 is both stylish and practical, featuring aerodynamic lines that enhance fuel efficiency while asserting a modern aesthetic. Available in various colors and finishes, this vehicle offers personalization options that appeal to a wide range of customers.

In summary, Alamo 02984405 is a well-rounded vehicle that combines performance, technology, safety, and design. With its focus on user experience and environmental responsibility, it stands out as a reliable choice in the competitive automotive market.
Top Page Image Contents