Exmark Lazer ZHP manual Lower Roll BAR Installation

Page 19

3.2.2Raise the rear of the unit and support it with jack stands or equivalent support.

CAUTION

POTENTIAL HAZARD

♦Raising the rear of the unit for assembly relying solely on mechanical or hydraulic jacks could be dangerous.

WHAT CAN HAPPEN

♦The mechanical or hydraulic jacks may not be enough support or may malfunction allowing the unit to fall, which could cause injury.

HOW TO AVOID THE HAZARD

♦DO NOT rely solely on mechanical or hydraulic jacks for support. Use adequate jack stands or equivalent support.

3.2.3Remove the wheel nuts from both sides of the unit and retain for later use.

3.2.4Install the two lower roll bar tubes.

a)Locate the left and right lower roll bar tubes.

b)Align lower roll bar tubes along wheel motor channels as shown in Figure 2.

c)LOOSELY install lower roll bar hardware (four 3/8-16 x 1 capscrews, four spring disk washers and four 3/8-16 whizlock nuts) from the bolt bag to the tubes on each side as shown in Figure 2.

NOTE: Be sure the spring disk washer cone is installed towards the head of the capscrew.

FIGURE 2

LOWER ROLL BAR INSTALLATION

3.2.5Install the upper u-shaped section of the roll bar. (Reference Figure 3 for alignment and installation instructions below):

a)Locate the latch pin assemblies (pin and hairpin connected with a lanyard).

b)Install a 1/2-13 x 3 1/4 capscrew in the washer on the lanyard of each pin assembly.

Note: Make sure the bent tab in the washer is towards the head of the bolt.

b)Lightly oil the inside surfaces of the ear-shaped plates at the upper end of the lower roll bar tubes.

-14 -

Page 18 Page 20
Image 19
Page 18 Page 20
Contents For Serial Nos 540,000 & Higher Potential Hazard Exmark Parts PLUS→ Program Operators Manual Table of Contents Training SafetyYour Safety is Involved Safety Alert SymbolCarbon monoxide can kill you Potential Hazard Operation Safe Zone for Mowing There is no rollover protection when the roll bar is down Maintenance and Storage Safety Signs Page Model Number SpecificationsEngine Electrical System Fuel SystemOperator Controls Tires and Wheels Hydrostatic Ground Drive SystemCutting Deck Curb Weight Assembly InstructionsDimensions Uncrate Mower Install Rollover Protection System Roll BARLower Roll BAR Installation Upper Roll BAR Installation Service BatteryMachine is shipped with a filled lead acid battery Install Seat Install Drive WheelsCheck Tire Pressure Control ARM Shaft Install Motion Control LeversService Engine Position Discharge ChuteMotion Control Positions Service Hydraulic OILOperation Instructions ControlsPush the lever forward and down to disengage the brake Mowing PRE-STARTStarting Engine Transporting Periodic Maintenance Maintenance & AdjustmentsService Interval Daily Service Interval Monthly Service Interval Daily or more often in dry conditionsBlade Bolt Installation Check rollover protections systems roll bar pins Service Interval 40 hr Service Interval 100 hrsService Interval 40 hrs Lubrication ChartService Interval Refer to chart Caster Wheel Assembly Service Interval Once YearlyService Interval 160 hrs Service Interval As Required Service Interval 80 hrsService Interval After First 250 hrs Then yearly thereafter Page Cutting Height Position AdjustmentsANTI-SCALP Roller Adjustment Swivel Adjustment Spring Compression Adjustment No adjustment necessary Brake AdjustmentThrottle Tension Potential Hazard LH Motion Control Adjustment RH Motion Control AdjustmentMotor OIL Disposal Battery DisposalCaster Adjustment Waste DisposalEngine will not Start Trouble ShootingMower Pulls Left or Right W/LEVERS Fully Forward Mower Cuts UnevenlyProblem Engine Troubleshooting TableElectrical Diagram Kawasaki Units Electrical Diagram Kohler Units Hydraulic Diagram Year Limited Warranty Service Record Page See EXMARK’S Complete Line of Accessories

Lazer ZHP specifications

The Exmark Lazer ZHP is a professional-grade zero-turn mower designed to deliver unparalleled performance and efficiency for commercial landscaping and maintenance. Recognized for its durability and innovative features, the Lazer ZHP series has become a preferred choice for professionals seeking precision and reliability in their mowing equipment.

One of the standout features of the Exmark Lazer ZHP is its powerful engine options, which typically include models from trusted manufacturers such as Kohler and Kawasaki. These engines are designed to provide robust performance while ensuring fuel efficiency, allowing operators to cover large areas without frequent refueling. The Lazer ZHP also boasts a high-capacity fuel tank, enhancing productivity by minimizing downtime due to refueling.

The mower’s cutting deck is another key highlight, with options typically ranging from 48 to 72 inches in size. The Exmark patented UltraCut deck technology provides an exceptional cut quality, ensuring that grass is finely mulched and evenly distributed. This not only enhances the visual appeal of the lawn but also contributes to overall lawn health by returning valuable nutrients to the soil.

In terms of comfort and ergonomics, the Lazer ZHP is built with the operator in mind. The spacious operator platform is designed to reduce fatigue during long hours of operation. The mower features an adjustable seat with premium cushioning, and the controls are intuitively positioned for easy access. The ergonomic design enhances maneuverability, allowing the operator to navigate tight spaces and obstacles with ease.

Technologically, the Exmark Lazer ZHP incorporates advanced features such as the Exmark patented IS (Independent Suspension) system. This technology enhances ride quality and stability, reducing the impact of uneven terrain on the operator and improving cut quality. Additionally, the mower is equipped with a sophisticated hydrostatic transmission, allowing for seamless speed and directional changes that enhance control and precision.

Another notable characteristic of the Lazer ZHP is its rugged construction, designed to withstand the rigors of commercial use. The welded steel frame and heavy-duty components are engineered to provide long-lasting performance and reliability, even in the most challenging conditions. The durable design not only enhances the mower’s lifespan but also reduces maintenance costs over time.

In summary, the Exmark Lazer ZHP stands out in the market for its combination of power, technology, and durability. With features that cater specifically to the needs of professional landscapers, this mower promises exceptional results and a superior mowing experience, making it an essential addition to any landscaping fleet.
Top Page Image Contents