Exmark Lazer ZHP manual Operation Instructions, Service Hydraulic OIL, Controls

Page 23

3.10 SERVICE HYDRAULIC OIL

The machine is shipped with hydraulic oil in the reservoir. Run the machine for approximately 15 minutes to allow any extra air to purge out of the hydraulic system. Check hydraulic reservoir and if necessary fill the reservoir to the appropriate level with Mobil 1 15W-50 synthetic motor oil. Replace hydraulic reservoir cap and tighten until snug. Do not overtighten.

NOTE: The baffle is labeled “HOT” and “COLD”. The oil level varies with the temperature of the oil. The “HOT” level shows the level of oil when it is at 225°F (107°C). The “COLD” level shows the level of the oil when it is at 75°F (24°C). Fill to the appropriate level depending upon the temperature of the oil. For example: If the oil is about 150° F (65°C). Fill to halfway between the “HOT” and “COLD” levels. If the oil is at room temperature (about 75° F (24°C)), fill only to the “COLD” level.

4.OPERATION INSTRUCTIONS

4.1CONTROLS

4.1.1Familiarize yourself with all controls before operating the mower.

4.1.2Motion Control Levers: Located on each side of the console.

The left lever controls the flow of hydraulic oil from the left hydrostatic pump to the left drive wheel motor. The right lever controls the flow of hydraulic oil from the right hydrostatic pump to the right drive wheel motor.

IMPORTANT: To begin movement (forward or backward) the operator must be in the seat, the brake lever must be disengaged (pushed down) before the motion control levers can be moved in or the engine will kill.

When levers are centered in the T-slot the drive system is in the neutral position. With levers moved out in the T-slot the drive system is in the neutral lock position (See Figure 6).

FIGURE 6

MOTION CONTROL POSITIONS

By moving both levers an equal amount forward or back from the neutral position the machine can be caused to move forward or backward in a straight line.

Movement of the left lever forward will cause the left drive wheel to rotate in a forward direction. Movement of the right lever forward will cause the right drive wheel to rotate in a forward direction. To stop forward travel, pull the levers back to the neutral position.

To turn left while moving forward, move the left lever back toward neutral to slow the left drive wheel. To turn right while moving forward, move the right lever back toward neutral to slow the right drive wheel.

To make a zero turn to the left, pull the left lever back beyond neutral while holding the right lever slightly ahead of neutral.

To make a zero turn to the right, pull the right lever back beyond neutral while holding the left lever slightly ahead of neutral.

- 18 -

Page 22 Page 24
Image 23
Page 22 Page 24
Contents For Serial Nos 540,000 & Higher Potential Hazard Exmark Parts PLUS→ Program Operators Manual Table of Contents Training SafetyYour Safety is Involved Safety Alert SymbolCarbon monoxide can kill you Potential Hazard Operation Safe Zone for Mowing There is no rollover protection when the roll bar is down Maintenance and Storage Safety Signs Page Engine SpecificationsModel Number Operator Controls Fuel SystemElectrical System Cutting Deck Hydrostatic Ground Drive SystemTires and Wheels Curb Weight Assembly InstructionsDimensions Uncrate Mower Install Rollover Protection System Roll BARLower Roll BAR Installation Machine is shipped with a filled lead acid battery Service BatteryUpper Roll BAR Installation Check Tire Pressure Install Drive WheelsInstall Seat Control ARM Shaft Install Motion Control LeversService Engine Position Discharge ChuteMotion Control Positions Service Hydraulic OILOperation Instructions ControlsPush the lever forward and down to disengage the brake Mowing PRE-STARTStarting Engine Transporting Service Interval Daily Maintenance & AdjustmentsPeriodic Maintenance Service Interval Monthly Service Interval Daily or more often in dry conditionsBlade Bolt Installation Check rollover protections systems roll bar pins Service Interval 40 hr Service Interval 100 hrsService Interval Refer to chart Lubrication ChartService Interval 40 hrs Service Interval 160 hrs Service Interval Once YearlyCaster Wheel Assembly Service Interval After First 250 hrs Then yearly thereafter Service Interval 80 hrsService Interval As Required Page Cutting Height Position AdjustmentsANTI-SCALP Roller Adjustment Swivel Adjustment Spring Compression Adjustment Throttle Tension Brake AdjustmentNo adjustment necessary Potential Hazard LH Motion Control Adjustment RH Motion Control AdjustmentMotor OIL Disposal Battery DisposalCaster Adjustment Waste DisposalEngine will not Start Trouble ShootingMower Pulls Left or Right W/LEVERS Fully Forward Mower Cuts UnevenlyProblem Engine Troubleshooting TableElectrical Diagram Kawasaki Units Electrical Diagram Kohler Units Hydraulic Diagram Year Limited Warranty Service Record Page See EXMARK’S Complete Line of Accessories

Lazer ZHP specifications

The Exmark Lazer ZHP is a professional-grade zero-turn mower designed to deliver unparalleled performance and efficiency for commercial landscaping and maintenance. Recognized for its durability and innovative features, the Lazer ZHP series has become a preferred choice for professionals seeking precision and reliability in their mowing equipment.

One of the standout features of the Exmark Lazer ZHP is its powerful engine options, which typically include models from trusted manufacturers such as Kohler and Kawasaki. These engines are designed to provide robust performance while ensuring fuel efficiency, allowing operators to cover large areas without frequent refueling. The Lazer ZHP also boasts a high-capacity fuel tank, enhancing productivity by minimizing downtime due to refueling.

The mower’s cutting deck is another key highlight, with options typically ranging from 48 to 72 inches in size. The Exmark patented UltraCut deck technology provides an exceptional cut quality, ensuring that grass is finely mulched and evenly distributed. This not only enhances the visual appeal of the lawn but also contributes to overall lawn health by returning valuable nutrients to the soil.

In terms of comfort and ergonomics, the Lazer ZHP is built with the operator in mind. The spacious operator platform is designed to reduce fatigue during long hours of operation. The mower features an adjustable seat with premium cushioning, and the controls are intuitively positioned for easy access. The ergonomic design enhances maneuverability, allowing the operator to navigate tight spaces and obstacles with ease.

Technologically, the Exmark Lazer ZHP incorporates advanced features such as the Exmark patented IS (Independent Suspension) system. This technology enhances ride quality and stability, reducing the impact of uneven terrain on the operator and improving cut quality. Additionally, the mower is equipped with a sophisticated hydrostatic transmission, allowing for seamless speed and directional changes that enhance control and precision.

Another notable characteristic of the Lazer ZHP is its rugged construction, designed to withstand the rigors of commercial use. The welded steel frame and heavy-duty components are engineered to provide long-lasting performance and reliability, even in the most challenging conditions. The durable design not only enhances the mower’s lifespan but also reduces maintenance costs over time.

In summary, the Exmark Lazer ZHP stands out in the market for its combination of power, technology, and durability. With features that cater specifically to the needs of professional landscapers, this mower promises exceptional results and a superior mowing experience, making it an essential addition to any landscaping fleet.
Top Page Image Contents