Exmark Lazer ZHP manual RH Motion Control Adjustment, LH Motion Control Adjustment

Page 42

NOTE: The nuts to the rear of the unit on each rod have left-hand threads.

 

TURN BOLT

REVERSE

 

 

INDICATOR

 

 

HERE

 

 

 

 

 

END OF

 

LOOSEN

 

SLOT

 

 

 

 

HERE

 

 

 

 

YOKE

 

 

TURN HERE

LOOSEN HERE

LOOSEN HERE

TO ADJUST

(RIGHTHAND THREAD)

(LEFTHAND THREAD)

FIGURE 14

RH MOTION CONTROL ADJUSTMENT

f)Start engine. Brake must be engaged and motion control levers out to start engine. Operator does not have to be in the seat because of the jumper wire being used. Run engine at full throttle and release brake.

g)The reverse indicator spring must be correct before the following adjustments can be made. See Section 5.2.10.

NOTE: The motion control lever needs to be in neutral while making any necessary adjustments.

The left rod assembly controls the left wheel and the right rod assembly controls the right wheel.

h)Bring the RH motion control lever into the neutral position. Adjust RH pump control rod length by rotating the double nuts on the rod in the appropriate direction until the wheels slightly creep in reverse. (See Figure 14). Move the motion control lever to the reverse position and while applying slight pressure to the lever, allow the reverse indicator spring to bring the levers back to neutral. The wheel must stop turning or slightly creep in reverse. When adjustment is complete, tighten lock nuts onto ball joints.

i)Bring the LH motion control lever into the neutral position. Adjust the LH pump control rod length by rotating the tracking adjustment knob in the appropriate direction until the wheels slightly creep in reverse. Move the motion control lever to the reverse position and while applying slight pressure to the lever allow the reverse indicator spring to bring the levers back to neutral. The wheel must stop turning or slightly creep in reverse. See Figure 15.

FIGURE 15

LH MOTION CONTROL ADJUSTMENT

- 37 -

Page 41 Page 43
Image 42
Page 41 Page 43
Contents For Serial Nos 540,000 & Higher Potential Hazard Exmark Parts PLUS→ Program Operators Manual Table of Contents Safety Alert Symbol SafetyYour Safety is Involved TrainingCarbon monoxide can kill you Potential Hazard Operation Safe Zone for Mowing There is no rollover protection when the roll bar is down Maintenance and Storage Safety Signs Page Specifications Model NumberEngine Fuel System Electrical SystemOperator Controls Hydrostatic Ground Drive System Tires and WheelsCutting Deck Uncrate Mower Install Rollover Protection System Roll BAR Assembly InstructionsDimensions Curb WeightLower Roll BAR Installation Service Battery Upper Roll BAR InstallationMachine is shipped with a filled lead acid battery Install Drive Wheels Install SeatCheck Tire Pressure Position Discharge Chute Install Motion Control LeversService Engine Control ARM ShaftControls Service Hydraulic OILOperation Instructions Motion Control PositionsPush the lever forward and down to disengage the brake PRE-START MowingStarting Engine Transporting Maintenance & Adjustments Periodic MaintenanceService Interval Daily Service Interval Daily or more often in dry conditions Service Interval MonthlyBlade Bolt Installation Check rollover protections systems roll bar pins Service Interval 100 hrs Service Interval 40 hrLubrication Chart Service Interval 40 hrsService Interval Refer to chart Service Interval Once Yearly Caster Wheel AssemblyService Interval 160 hrs Service Interval 80 hrs Service Interval As RequiredService Interval After First 250 hrs Then yearly thereafter Page Adjustments Cutting Height PositionANTI-SCALP Roller Adjustment Swivel Adjustment Spring Compression Adjustment Brake Adjustment No adjustment necessaryThrottle Tension Potential Hazard RH Motion Control Adjustment LH Motion Control AdjustmentWaste Disposal Battery DisposalCaster Adjustment Motor OIL DisposalMower Cuts Unevenly Trouble ShootingMower Pulls Left or Right W/LEVERS Fully Forward Engine will not StartEngine Troubleshooting Table ProblemElectrical Diagram Kawasaki Units Electrical Diagram Kohler Units Hydraulic Diagram Year Limited Warranty Service Record Page See EXMARK’S Complete Line of Accessories

Lazer ZHP specifications

The Exmark Lazer ZHP is a professional-grade zero-turn mower designed to deliver unparalleled performance and efficiency for commercial landscaping and maintenance. Recognized for its durability and innovative features, the Lazer ZHP series has become a preferred choice for professionals seeking precision and reliability in their mowing equipment.

One of the standout features of the Exmark Lazer ZHP is its powerful engine options, which typically include models from trusted manufacturers such as Kohler and Kawasaki. These engines are designed to provide robust performance while ensuring fuel efficiency, allowing operators to cover large areas without frequent refueling. The Lazer ZHP also boasts a high-capacity fuel tank, enhancing productivity by minimizing downtime due to refueling.

The mower’s cutting deck is another key highlight, with options typically ranging from 48 to 72 inches in size. The Exmark patented UltraCut deck technology provides an exceptional cut quality, ensuring that grass is finely mulched and evenly distributed. This not only enhances the visual appeal of the lawn but also contributes to overall lawn health by returning valuable nutrients to the soil.

In terms of comfort and ergonomics, the Lazer ZHP is built with the operator in mind. The spacious operator platform is designed to reduce fatigue during long hours of operation. The mower features an adjustable seat with premium cushioning, and the controls are intuitively positioned for easy access. The ergonomic design enhances maneuverability, allowing the operator to navigate tight spaces and obstacles with ease.

Technologically, the Exmark Lazer ZHP incorporates advanced features such as the Exmark patented IS (Independent Suspension) system. This technology enhances ride quality and stability, reducing the impact of uneven terrain on the operator and improving cut quality. Additionally, the mower is equipped with a sophisticated hydrostatic transmission, allowing for seamless speed and directional changes that enhance control and precision.

Another notable characteristic of the Lazer ZHP is its rugged construction, designed to withstand the rigors of commercial use. The welded steel frame and heavy-duty components are engineered to provide long-lasting performance and reliability, even in the most challenging conditions. The durable design not only enhances the mower’s lifespan but also reduces maintenance costs over time.

In summary, the Exmark Lazer ZHP stands out in the market for its combination of power, technology, and durability. With features that cater specifically to the needs of professional landscapers, this mower promises exceptional results and a superior mowing experience, making it an essential addition to any landscaping fleet.
Top Page Image Contents