Exmark Lazer ZHP manual Install Motion Control Levers, Position Discharge Chute, Service Engine

Page 22

b)Remove the four 5/16-18 whizlock nuts from the seat track studs at the bottom of the seat. Retain for use later.

c)Align the seat track studs on the bottom of the seat with the holes in the seat frame. Place seat on top of the frame and secure with the four 5/16-18 whizlock nuts remove in step b).

3.7INSTALL MOTION CONTROL LEVERS

3.7.1Loosen and remove the two (2) 3/8” x 1” bolts and spring disc washers which attach the motion control levers to the control arm shafts for shipping and the two (2) 3/8” x 1” bolts and spring disc washers which are screwed into the control arm shafts.

a)Install the left motion control lever onto the control arm shaft (See Figure 4) on the left side of the console. Place the lever (with the mounting plate towards the rear) on the outside of the control arm shaft and secure with the bolts and washers. Position the lever so the bolts are in the center of the slots on the lever mounting plate and tighten until snug. Repeat on opposite side of unit.

NOTE: There are two lever height options available. Place the levers in the top two holes to increase height of the levers, or in the bottom two holes to decrease the height of the levers.

If the levers do not align with each other, when in the neutral position, (See Figure 5) loosen the hardware and make the appropriate adjustment by sliding/tilting the lever(s) forward or backward until properly aligned and tighten hardware.

MOTION

CONTROL

LEVER

LEVERS IN

ALIGNMENT

MOUNT PLATE TO

THE REAR & OUTSIDE

OF ARM SHAFT

FIGURE 4

FIGURE 5

CONTROL ARM SHAFT

LEVER ALIGNMENT

b)If the ends of the levers hit against each other, while in the drive position (levers rotated in as far as possible), make adjustments by moving the levers outwards to the neutral lock position and carefully bending them outward. Move them back to the drive position and check for clearance, repeat if necessary.

3.8POSITION DISCHARGE CHUTE

3.8.1Loosen two (2) 5/16” nyloc nuts attaching discharge chute. Lower the discharge chute into position. Retighten nyloc nuts until chute is snug but can pivot freely.

3.9SERVICE ENGINE

Engine is shipped with oil, check oil level and if necessary fill to the appropriate level with SAE 10W-30 or 10W-40, AP1 service class SF or SG for operating in temperatures above 0° F (-18°C). See Engine Operator's Manual.

- 17 -

Page 21 Page 23
Image 22
Page 21 Page 23
Contents For Serial Nos 540,000 & Higher Potential Hazard Exmark Parts PLUS→ Program Operators Manual Table of Contents Safety Alert Symbol SafetyYour Safety is Involved TrainingCarbon monoxide can kill you Potential Hazard Operation Safe Zone for Mowing There is no rollover protection when the roll bar is down Maintenance and Storage Safety Signs Page Model Number SpecificationsEngine Electrical System Fuel SystemOperator Controls Tires and Wheels Hydrostatic Ground Drive SystemCutting Deck Uncrate Mower Install Rollover Protection System Roll BAR Assembly InstructionsDimensions Curb WeightLower Roll BAR Installation Upper Roll BAR Installation Service BatteryMachine is shipped with a filled lead acid battery Install Seat Install Drive WheelsCheck Tire Pressure Position Discharge Chute Install Motion Control LeversService Engine Control ARM ShaftControls Service Hydraulic OILOperation Instructions Motion Control PositionsPush the lever forward and down to disengage the brake PRE-START MowingStarting Engine Transporting Periodic Maintenance Maintenance & AdjustmentsService Interval Daily Service Interval Daily or more often in dry conditions Service Interval MonthlyBlade Bolt Installation Check rollover protections systems roll bar pins Service Interval 100 hrs Service Interval 40 hrService Interval 40 hrs Lubrication ChartService Interval Refer to chart Caster Wheel Assembly Service Interval Once YearlyService Interval 160 hrs Service Interval As Required Service Interval 80 hrsService Interval After First 250 hrs Then yearly thereafter Page Adjustments Cutting Height PositionANTI-SCALP Roller Adjustment Swivel Adjustment Spring Compression Adjustment No adjustment necessary Brake AdjustmentThrottle Tension Potential Hazard RH Motion Control Adjustment LH Motion Control AdjustmentWaste Disposal Battery DisposalCaster Adjustment Motor OIL DisposalMower Cuts Unevenly Trouble ShootingMower Pulls Left or Right W/LEVERS Fully Forward Engine will not StartEngine Troubleshooting Table ProblemElectrical Diagram Kawasaki Units Electrical Diagram Kohler Units Hydraulic Diagram Year Limited Warranty Service Record Page See EXMARK’S Complete Line of Accessories

Lazer ZHP specifications

The Exmark Lazer ZHP is a professional-grade zero-turn mower designed to deliver unparalleled performance and efficiency for commercial landscaping and maintenance. Recognized for its durability and innovative features, the Lazer ZHP series has become a preferred choice for professionals seeking precision and reliability in their mowing equipment.

One of the standout features of the Exmark Lazer ZHP is its powerful engine options, which typically include models from trusted manufacturers such as Kohler and Kawasaki. These engines are designed to provide robust performance while ensuring fuel efficiency, allowing operators to cover large areas without frequent refueling. The Lazer ZHP also boasts a high-capacity fuel tank, enhancing productivity by minimizing downtime due to refueling.

The mower’s cutting deck is another key highlight, with options typically ranging from 48 to 72 inches in size. The Exmark patented UltraCut deck technology provides an exceptional cut quality, ensuring that grass is finely mulched and evenly distributed. This not only enhances the visual appeal of the lawn but also contributes to overall lawn health by returning valuable nutrients to the soil.

In terms of comfort and ergonomics, the Lazer ZHP is built with the operator in mind. The spacious operator platform is designed to reduce fatigue during long hours of operation. The mower features an adjustable seat with premium cushioning, and the controls are intuitively positioned for easy access. The ergonomic design enhances maneuverability, allowing the operator to navigate tight spaces and obstacles with ease.

Technologically, the Exmark Lazer ZHP incorporates advanced features such as the Exmark patented IS (Independent Suspension) system. This technology enhances ride quality and stability, reducing the impact of uneven terrain on the operator and improving cut quality. Additionally, the mower is equipped with a sophisticated hydrostatic transmission, allowing for seamless speed and directional changes that enhance control and precision.

Another notable characteristic of the Lazer ZHP is its rugged construction, designed to withstand the rigors of commercial use. The welded steel frame and heavy-duty components are engineered to provide long-lasting performance and reliability, even in the most challenging conditions. The durable design not only enhances the mower’s lifespan but also reduces maintenance costs over time.

In summary, the Exmark Lazer ZHP stands out in the market for its combination of power, technology, and durability. With features that cater specifically to the needs of professional landscapers, this mower promises exceptional results and a superior mowing experience, making it an essential addition to any landscaping fleet.
Top Page Image Contents