Exmark Lazer ZHP manual Transporting

Page 27

Before stopping the engine, place the throttle control midway between the “slow” and “fast” positions. Allow the engine to run a minimum of 15 seconds; then stop the engine.

Rotate ignition switch to “OFF” position. Remove the key to prevent children or other unauthorized persons from starting engine.

Close fuel shut-off valve when machine will not be used for a few days, when transporting, and when the unit is parked inside a building.

4.4TRANSPORTING

4.4.1Transporting a Unit: Use a heavy-duty trailer or truck to transport the machine. Lock brake and block wheels. Securely fasten the machine to the trailer or truck with straps, chains, cable, or ropes. Be sure that the trailer or truck has all necessary lighting and marking as required by law.

Secure a trailer with a safety chain.

CAUTION

POTENTIAL HAZARD

♦This unit does not have proper turn signals, lights, reflective markings, or a slow moving vehicle emblem. These items are required to drive on a public street or roadway.

WHAT CAN HAPPEN

♦Driving on a street or roadway without such equipment is dangerous and can lead to accidents causing personal injury.

♦Driving on a street or roadway without such equipment may also be a violation of State laws and the operator may be subject to traffic tickets and/or fines.

HOW TO AVOID THE HAZARD

♦Do not drive a unit on a public street or roadway.

WARNING

POTENTIAL HAZARD

♦Loading a unit on a trailer or truck increases the possibility of backward tip-over.

WHAT CAN HAPPEN

♦Backward tip-over of the unit could cause serious injury or death.

HOW TO AVOID THE HAZARD

♦Use extreme caution when operating a unit on a ramp.

♦Use only a single, full width ramp; DO NOT use individual ramps for each side of the unit.

♦If individual ramps must be used, use enough ramps to create an unbroken ramp surface wider than the unit.

♦DO NOT exceed a 15° angle between ramp and ground or between ramp and trailer or truck.

♦Avoid sudden acceleration while driving unit up a ramp to avoid tipping backward.

♦Avoid sudden deceleration while backing unit down a ramp to avoid tipping backward.

-22 -

Page 26 Page 28
Image 27
Page 26 Page 28
Contents For Serial Nos 540,000 & Higher Potential Hazard Exmark Parts PLUS→ Program Operators Manual Table of Contents Training SafetyYour Safety is Involved Safety Alert SymbolCarbon monoxide can kill you Potential Hazard Operation Safe Zone for Mowing There is no rollover protection when the roll bar is down Maintenance and Storage Safety Signs Page Specifications Model NumberEngine Fuel System Electrical SystemOperator Controls Hydrostatic Ground Drive System Tires and WheelsCutting Deck Curb Weight Assembly InstructionsDimensions Uncrate Mower Install Rollover Protection System Roll BARLower Roll BAR Installation Service Battery Upper Roll BAR InstallationMachine is shipped with a filled lead acid battery Install Drive Wheels Install SeatCheck Tire Pressure Control ARM Shaft Install Motion Control LeversService Engine Position Discharge ChuteMotion Control Positions Service Hydraulic OILOperation Instructions ControlsPush the lever forward and down to disengage the brake Mowing PRE-STARTStarting Engine Transporting Maintenance & Adjustments Periodic MaintenanceService Interval Daily Service Interval Monthly Service Interval Daily or more often in dry conditionsBlade Bolt Installation Check rollover protections systems roll bar pins Service Interval 40 hr Service Interval 100 hrsLubrication Chart Service Interval 40 hrsService Interval Refer to chart Service Interval Once Yearly Caster Wheel AssemblyService Interval 160 hrs Service Interval 80 hrs Service Interval As RequiredService Interval After First 250 hrs Then yearly thereafter Page Cutting Height Position AdjustmentsANTI-SCALP Roller Adjustment Swivel Adjustment Spring Compression Adjustment Brake Adjustment No adjustment necessaryThrottle Tension Potential Hazard LH Motion Control Adjustment RH Motion Control AdjustmentMotor OIL Disposal Battery DisposalCaster Adjustment Waste DisposalEngine will not Start Trouble ShootingMower Pulls Left or Right W/LEVERS Fully Forward Mower Cuts UnevenlyProblem Engine Troubleshooting TableElectrical Diagram Kawasaki Units Electrical Diagram Kohler Units Hydraulic Diagram Year Limited Warranty Service Record Page See EXMARK’S Complete Line of Accessories

Lazer ZHP specifications

The Exmark Lazer ZHP is a professional-grade zero-turn mower designed to deliver unparalleled performance and efficiency for commercial landscaping and maintenance. Recognized for its durability and innovative features, the Lazer ZHP series has become a preferred choice for professionals seeking precision and reliability in their mowing equipment.

One of the standout features of the Exmark Lazer ZHP is its powerful engine options, which typically include models from trusted manufacturers such as Kohler and Kawasaki. These engines are designed to provide robust performance while ensuring fuel efficiency, allowing operators to cover large areas without frequent refueling. The Lazer ZHP also boasts a high-capacity fuel tank, enhancing productivity by minimizing downtime due to refueling.

The mower’s cutting deck is another key highlight, with options typically ranging from 48 to 72 inches in size. The Exmark patented UltraCut deck technology provides an exceptional cut quality, ensuring that grass is finely mulched and evenly distributed. This not only enhances the visual appeal of the lawn but also contributes to overall lawn health by returning valuable nutrients to the soil.

In terms of comfort and ergonomics, the Lazer ZHP is built with the operator in mind. The spacious operator platform is designed to reduce fatigue during long hours of operation. The mower features an adjustable seat with premium cushioning, and the controls are intuitively positioned for easy access. The ergonomic design enhances maneuverability, allowing the operator to navigate tight spaces and obstacles with ease.

Technologically, the Exmark Lazer ZHP incorporates advanced features such as the Exmark patented IS (Independent Suspension) system. This technology enhances ride quality and stability, reducing the impact of uneven terrain on the operator and improving cut quality. Additionally, the mower is equipped with a sophisticated hydrostatic transmission, allowing for seamless speed and directional changes that enhance control and precision.

Another notable characteristic of the Lazer ZHP is its rugged construction, designed to withstand the rigors of commercial use. The welded steel frame and heavy-duty components are engineered to provide long-lasting performance and reliability, even in the most challenging conditions. The durable design not only enhances the mower’s lifespan but also reduces maintenance costs over time.

In summary, the Exmark Lazer ZHP stands out in the market for its combination of power, technology, and durability. With features that cater specifically to the needs of professional landscapers, this mower promises exceptional results and a superior mowing experience, making it an essential addition to any landscaping fleet.
Top Page Image Contents