Exmark Lazer ZHP manual Check rollover protections systems roll bar pins

Page 31

CAUTION

POTENTIAL HAZARD

♦Operating a mower deck with loose or weakened blade bolts can be dangerous.

WHAT CAN HAPPEN

♦A loose or weakened blade bolt could allow a blade rotating at a high speed to come out from under the deck, causing serious injury or property damage.

HOW TO AVOID THE HAZARD

♦Always re-install original Exmark blades, blade bushings, spring disc washers, and blade bolts in the correct positions as shown.

5.1.6Check safety interlock system.

Service Interval: Daily

a)Check starting circuit. Starter should crank with parking brake engaged, PTO disengaged and motion control levers moved out in the neutral lock position. The operator does not need to be in the seat to start the engine.

Try to start with operator in seat, parking brake disengaged, PTO disengaged and motion control levers in the neutral lock position - starter must not crank.

Try to start with operator in seat, parking brake engaged, PTO engaged and motion control levers in the neutral lock position - starter must not crank.

Try to start with operator in seat, parking brake engaged, PTO disengaged, and the left motion control lever in, starter must not crank, repeat again with the right lever in, then with both levers in - starter must not crank.

b)Check kill circuits. Run engine at one-third throttle, disengage parking brake and raise off of seat (but do not get off of machine) engine must stop after approx. 1/2 second has elapsed (seat has time delay kill switch to prevent cut-outs on rough terrain).

Run engine at one-third throttle, engage PTO and raise off of seat (but do not get off of machine) engine must stop after 1/2 second has elapsed.

Run engine at one-third throttle, with brake disengaged, move levers in and raise off seat (but do not get off of machine) engine must stop after 1/2 second has elapsed.

Again, run engine at one-third throttle, brake engaged, and move left motion control lever in - engine must stop.

Repeat again moving the right lever in, then moving both levers in - engine must stop whether operator is on seat or not.

NOTE: If machine does not pass any of these tests, do not operate. Contact your authorized EXMARK SERVICE DEALER.

IMPORTANT: It is essential that operator safety mechanisms be connected and in proper operating condition prior to use for mowing.

5.1.7Check rollover protections systems (roll bar) pins

Service Interval: Daily

a)Make sure latch pin and hair pin are fully installed and lanyard is in good condition.

-26 -

Page 30 Page 32
Image 31
Page 30 Page 32
Contents For Serial Nos 540,000 & Higher Potential Hazard Exmark Parts PLUS→ Program Operators Manual Table of Contents Training SafetyYour Safety is Involved Safety Alert SymbolCarbon monoxide can kill you Potential Hazard Operation Safe Zone for Mowing There is no rollover protection when the roll bar is down Maintenance and Storage Safety Signs Page Model Number SpecificationsEngine Electrical System Fuel SystemOperator Controls Tires and Wheels Hydrostatic Ground Drive SystemCutting Deck Curb Weight Assembly InstructionsDimensions Uncrate Mower Install Rollover Protection System Roll BARLower Roll BAR Installation Upper Roll BAR Installation Service BatteryMachine is shipped with a filled lead acid battery Install Seat Install Drive WheelsCheck Tire Pressure Control ARM Shaft Install Motion Control LeversService Engine Position Discharge ChuteMotion Control Positions Service Hydraulic OILOperation Instructions ControlsPush the lever forward and down to disengage the brake Mowing PRE-STARTStarting Engine Transporting Periodic Maintenance Maintenance & AdjustmentsService Interval Daily Service Interval Monthly Service Interval Daily or more often in dry conditionsBlade Bolt Installation Check rollover protections systems roll bar pins Service Interval 40 hr Service Interval 100 hrsService Interval 40 hrs Lubrication ChartService Interval Refer to chart Caster Wheel Assembly Service Interval Once YearlyService Interval 160 hrs Service Interval As Required Service Interval 80 hrsService Interval After First 250 hrs Then yearly thereafter Page Cutting Height Position AdjustmentsANTI-SCALP Roller Adjustment Swivel Adjustment Spring Compression Adjustment No adjustment necessary Brake AdjustmentThrottle Tension Potential Hazard LH Motion Control Adjustment RH Motion Control AdjustmentMotor OIL Disposal Battery DisposalCaster Adjustment Waste DisposalEngine will not Start Trouble ShootingMower Pulls Left or Right W/LEVERS Fully Forward Mower Cuts UnevenlyProblem Engine Troubleshooting TableElectrical Diagram Kawasaki Units Electrical Diagram Kohler Units Hydraulic Diagram Year Limited Warranty Service Record Page See EXMARK’S Complete Line of Accessories

Lazer ZHP specifications

The Exmark Lazer ZHP is a professional-grade zero-turn mower designed to deliver unparalleled performance and efficiency for commercial landscaping and maintenance. Recognized for its durability and innovative features, the Lazer ZHP series has become a preferred choice for professionals seeking precision and reliability in their mowing equipment.

One of the standout features of the Exmark Lazer ZHP is its powerful engine options, which typically include models from trusted manufacturers such as Kohler and Kawasaki. These engines are designed to provide robust performance while ensuring fuel efficiency, allowing operators to cover large areas without frequent refueling. The Lazer ZHP also boasts a high-capacity fuel tank, enhancing productivity by minimizing downtime due to refueling.

The mower’s cutting deck is another key highlight, with options typically ranging from 48 to 72 inches in size. The Exmark patented UltraCut deck technology provides an exceptional cut quality, ensuring that grass is finely mulched and evenly distributed. This not only enhances the visual appeal of the lawn but also contributes to overall lawn health by returning valuable nutrients to the soil.

In terms of comfort and ergonomics, the Lazer ZHP is built with the operator in mind. The spacious operator platform is designed to reduce fatigue during long hours of operation. The mower features an adjustable seat with premium cushioning, and the controls are intuitively positioned for easy access. The ergonomic design enhances maneuverability, allowing the operator to navigate tight spaces and obstacles with ease.

Technologically, the Exmark Lazer ZHP incorporates advanced features such as the Exmark patented IS (Independent Suspension) system. This technology enhances ride quality and stability, reducing the impact of uneven terrain on the operator and improving cut quality. Additionally, the mower is equipped with a sophisticated hydrostatic transmission, allowing for seamless speed and directional changes that enhance control and precision.

Another notable characteristic of the Lazer ZHP is its rugged construction, designed to withstand the rigors of commercial use. The welded steel frame and heavy-duty components are engineered to provide long-lasting performance and reliability, even in the most challenging conditions. The durable design not only enhances the mower’s lifespan but also reduces maintenance costs over time.

In summary, the Exmark Lazer ZHP stands out in the market for its combination of power, technology, and durability. With features that cater specifically to the needs of professional landscapers, this mower promises exceptional results and a superior mowing experience, making it an essential addition to any landscaping fleet.
Top Page Image Contents