Exmark 4500-367 manual Check Engine Oil Level, Check Battery Charge

Page 22

Maintenance

Maintenance Service

Maintenance Procedure

Interval

 

 

 

 

 

Monthly

Check the battery charge.

 

 

 

Yearly

Lubricate grease fittings.

• Lubricate the caster wheel hubs.

 

 

 

 

Periodic Maintenance

Check Engine Oil Level

Service Interval: Before each use or daily

1.Stop engine and wait for all moving parts to stop. Make sure unit is on a level surface.

2.Check with engine cold.

3.Raise hopper.

4.Clean area around dipstick. Remove dipstick and wipe oil off. Reinsert the dipstick and push it all the way down into the tube. Remove the dipstick and read the oil level.

5.If the oil level is low, wipe off the area around the oil fill cap, remove cap and fill to the “FULL” mark on the dipstick. Use oil as specified in Engine Owner’s Manual. Do Not overfill.

Important: Do Not operate the engine with the oil level below the “LOW” (or “ADD”) mark on the dipstick, or over the “FULL” mark.

Check Battery Charge

Service Interval: Monthly

WARNING

CALIFORNIA

Proposition 65 Warning

Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling.

Allowing batteries to stand for an extended period of time without recharging them will result in reduced performance and service life. To preserve optimum battery performance and life, recharge batteries in storage when the open circuit voltage drops to 12.4 volts.

Note: To prevent damage due to freezing, battery should be fully charged before putting away for winter storage.

Check the voltage of the battery with a digital voltmeter. Locate the voltage reading of the battery in the table and charge the battery for the recommended time interval to bring the charge up to a full charge of 12.6 volts or greater.

Important: Make sure the negative battery cables are disconnected and the battery charger used for charging the battery has an output of 16 volts and 7 amps or less to avoid damaging the battery (see chart for recommended charger settings).

Voltage

Percent

Maximum

Charging

Reading

Charge

Charger

Interval

 

 

Settings

 

12.6 or

100%

16 volts/7

No

greater

 

amps

Charging

 

 

 

Required

12.4 – 12.6

75–100%

16 volts/7

30 Minutes

 

 

amps

 

12.2 – 12.4

50–75%

16 volts/7

1 Hour

 

 

amps

 

12.0–12.2

25–50%

14.4 volts/4

2 Hours

 

 

amps

 

11.7–12.0

0–25%

14.4 volts/4

3 Hours

 

 

amps

 

11.7 or less

0%

14.4 volts/2

6 Hours or

 

 

amps

More

22

Image 22
Contents Navigator California Introduction Contents Safe Operating Practices SafetySafety Alert Symbol TrainingSafety Operation Slope Operation Maintenance and Storage Safety and Instructional Decals 103-9034 103-9724 109-4273 109-4638 109-7318 116-0404 116-1175 Molded in LH Console Molded into Front of Hopper Model Numbers SpecificationsSystems Dimensions Product Overview Curb WeightTorque Requirements Operation ControlsPre-Start Operating InstructionsStopping the Engine Engaging the PTODisengaging the PTO Driving the MachineClearing Hopper Screen TransportingEmptying Hopper Transporting a UnitLoading a Unit Maintenance Recommended Maintenance SchedulesCheck Battery Charge Check Engine Oil LevelCheck for Loose Hardware Check Safety Interlock SystemService Air Cleaner Change Engine OilCheck Condition Of Belts Check Hydraulic Oil LevelCheck Tire Pressures Lubricate Grease FittingsService Interval Yearly Lubricate Rear Caster Wheel HubsLubricate Steering Linkage Rod Ends Lubricate Brake Handle PivotLubricate Brake Rod Bushings Lubricate Hopper ActuatorChange Hydraulic System Filter Check Wheel Hub Locknuts Fuel Tank Mounting Hardware SpecificationsPTO Belt Replacement Check Wheel Lug NutsPump Drive Belt Replacement Belt Guide AdjustmentBrake Adjustment Adjust Safety SwitchAdjust Speed Control Lever Tension Speed Control Linkage Adjustment Response Adjustment Steering Control LeverPTO Drive Pulley Alignment Tracking AdjustmentPump Drive Pulley Alignment Hopper Door Adjustment Rear Caster Pivot Bearings Pre-Load AdjustmentPTO Brake Spring Adjustment Clean Debris From Machine Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Waste DisposalTroubleshooting Problem Possible Cause Corrective ActionTroubleshooting Schematics Electrical DiagramElectrical Logic Schematic StartHydraulic Diagram Exmark Commercial Turf Equipment Page Page See EXMARK’S Complete Line of Accessories and Options