Exmark 4500-367 manual Change Hydraulic System Filter

Page 27

Maintenance

Change Hydraulic System Filter

Service Interval: After the first 250 hours

Every 500 hours/Yearly (whichever comes first) thereafter

(Every 250 hours/Yearly if using Mobil 1 15W50)

Note: Use only Exmark Part No. 109-0071 for Summer use above 32°F (0°C) or P/N 1-523541 for Winter use below 32°F (0°C). (Refer to the Hydrostatic Ground Drive System section in Specifications for filter specifications.)

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Carefully clean area around filter. It is important that no dirt or contamination enter hydraulic system.

3.Unscrew filter to remove and allow oil to drain from reservoir.

Important: Before reinstalling new filter, fill it with Exmark Premium Hydro oil and apply a thin coat of oil on the surface of the rubber seal.

Turn filter clockwise until rubber seal contacts the filter adapter, then tighten the filter an additional 2/3 to 3/4 turn.

4.Fill reservoir as stated in Check Hydraulic Oil Level section.

Exmark Premium Hydro Oil is recommended. Refer to the chart for an acceptable alternative:

Hydro Oil

Change Interval

 

 

Exmark Premium Hydro

500 Hours

Oil (Preferred)

 

Mobil 1 15W50

250 Hours

 

 

5.Raise the rear of machine up and support with jack stands (or equivalent support) just high enough to allow drive wheels to turn freely.

6.Start engine and move throttle control ahead to full throttle position. Move the speed control levers to the full speed and run for several minutes. Shut down machine and recheck oil level.

Note: Do Not change hydraulic system oil (except for what can be drained when changing filter), unless it is felt the oil has been contaminated or been extremely hot.

Changing oil unnecessarily could damage hydraulic system by introducing contaminates into the system.

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Navigator California Introduction Contents Training SafetySafety Alert Symbol Safe Operating PracticesSafety Operation Slope Operation Maintenance and Storage Safety and Instructional Decals 103-9034 103-9724 109-4273 109-4638 109-7318 116-0404 116-1175 Molded in LH Console Molded into Front of Hopper Specifications Model NumbersSystems Dimensions Curb Weight Product OverviewTorque Requirements Controls OperationOperating Instructions Pre-StartDriving the Machine Engaging the PTODisengaging the PTO Stopping the EngineTransporting a Unit TransportingEmptying Hopper Clearing Hopper ScreenLoading a Unit Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeChange Engine Oil Check Safety Interlock SystemService Air Cleaner Check for Loose HardwareLubricate Grease Fittings Check Hydraulic Oil LevelCheck Tire Pressures Check Condition Of BeltsLubricate Rear Caster Wheel Hubs Service Interval YearlyLubricate Hopper Actuator Lubricate Brake Handle PivotLubricate Brake Rod Bushings Lubricate Steering Linkage Rod EndsChange Hydraulic System Filter Check Wheel Lug Nuts Fuel Tank Mounting Hardware SpecificationsPTO Belt Replacement Check Wheel Hub LocknutsBelt Guide Adjustment Pump Drive Belt ReplacementAdjust Safety Switch Brake AdjustmentAdjust Speed Control Lever Tension Speed Control Linkage Adjustment Steering Control Lever Response AdjustmentTracking Adjustment PTO Drive Pulley AlignmentPump Drive Pulley Alignment Rear Caster Pivot Bearings Pre-Load Adjustment Hopper Door AdjustmentPTO Brake Spring Adjustment Waste Disposal Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Clean Debris From MachineProblem Possible Cause Corrective Action TroubleshootingTroubleshooting Electrical Diagram SchematicsStart Electrical Logic SchematicHydraulic Diagram Exmark Commercial Turf Equipment Page Page See EXMARK’S Complete Line of Accessories and Options
Top Page Image Contents