Crown Audio IQ P.I.P.-DSP manuals

27 pages293.81 Kb

An IQ System
Programmable Input Processor with DSP for Crown
-compatible Power Amplifiers
P.I.P.
WORLDWIDE
NORTH AMERICA
- Telephone: 219-294-8200. Facsimile: 219-294-8301 Telephone: 219-294-8200. Facsimile: 219-294-8301
2THREE YEAR FULL WARRANTY
- YEAR
  - YEAR
- 3Important Safety Instructions
  - Crown Audio Division Technical Support Group
- 4WARNING
  - FCC COMPLIANCE NOTICE
    - 5Quick Install Procedure
      - This procedure is provided for those who are already familiar with Crowns
      - and who would like to install the
      - Prepare the IQP.I.P.DSP:
      - Prepare the amplifier:
      - Install the IQP.I.P.DSP into the amplifier:
      - Install the wiring:
      - Adjust the levels and scale factors:
        Page 6
        IQP.I.P.DSP
        IQ System
        IOC
        IQP.I.P.DSP
- 6ILLUSTRATIONS
- CONTENTS
  - 1.1 Unpacking
- 71 Welcome
  - P. I. P.
- 82 Facilities
  - D. Reset Switch
  - 9P.I.P.
    - K.
    - E. Data Signal Presence Indicator (DSPI)
  - PIP2
    - F. Crown Bus Input Connector
    - G. External Power Input
    - H. Crown Bus Output Connector
    - I.
    - Edge Connector
    - J. Amplifier Output Pad Jumpers (JP4, JP5)
    - SIP Sockets (RN1, RN2)
    - L. IQ Circuit Board (Top)
    - M. Audio Circuit Board (Bottom)
    - N. IQ Address Switch (SW1)
- 3 Installation
- 10BOTTOM
  - DSP.
  - SMX-6
  - IQ-P.I.P.-DSP-PIP2
  - 3.1 Prepare the
  - IQP.I.P.DSP
    - IQ System
    - SW1
      - ON
  - SW1
    - 3.2 Prepare the Amplifier
    - 11IQP.I.P.DSP
      - 3.3 Install the
      - into the Amplifier
      - 3.4 Install the Wiring
        Section 3.8 for more information.
        IQ2
        IQINT II
        DSP
      - 123.5 Adjust the Levels & Scale Factors
        
        Users Manual
      - 3.6 A Closer Look at Crown Bus Wiring
        Multiloop Advantages
        Single Loop Advantages (with IQ-INT II interfaces)
        13IQ P.I.P.DSP
      - 143.7 A Closer Look at Audio Signal Wiring
      - 3.8 When External Power is Needed
  - 154 Operation
    - 4.1 Power/Standby Indicators
    - IOC
      - 4.2
      - Event Monitor
      - 4.3 Input Signal Level Monitor
      - 4.4 Output Signal Level Monitor
      - 4.5
      - Level Monitor
      - 4.6 Power Control
      - 4.7 Signal Mute
      - 164.8 Polarity Inverter
      - 4.9 Input Signal Attenuator
      - 4.10 Input Protection Limiter
      - 4.11 Auto
      - 4.12 Input Signal Compressor/Limiter
      - 4.13 Smooth/Output Signal Limiter
      - 4.14 Auto Standby
    - 17IOC
      - 4.17 Excessive
      - 4.15
      - 4.16 Excessive
        DSP
        ODEP
        IQ Systems
      - Limiter
      - Warning
        Note: An IOC event is one complete on-off-on cycle.
      - 184.18 Fault Warning
      - 4.19 Signal Delay
        Note: The signal delays are not disabled by the ASA control.
      - 4.20 Programmable Filters
        IQ System:
        Low-Pass Crossover Filter
        High-Pass Crossover Filter
      - 204.21 Memory Backup
      - 4.22 Amp Mode
        P.I.P.-FX
      - 4.23 Amplifier Information
      - 4.24 IQ2 Protocol Support
      - 4.25 Crown Bus Drop Out Relays
      - 4.26 Data Signal Presence Indicator
      - 4.27 Reset
      - 4.28 User Default Settings
  - 215 Technical Information
    - The purpose of the
      - ODEP
      - IQ System
    - to control and monitor a
    - is to provide extensive signal processing capabilities and to enable an
    - 5.1 Audio Signals
      - 5.1.1 Hardware Processing
      - 5.1.2 Signal Flow Processing
      - 5.2.3 DSPI Control
    - 22IQ System
      - ODEP
      - 5.3
      - Communications
      - 5.4 Microprocessors and Reset Switch
        IQ System
      - 5.2 Control/Monitor Functions
        5.2.1 Audio Signals
        5.2.2 Status Signals
        IOC
  - 236 Specifications
    - General
    - IQ System
      - Reference
      - 10000
      - Macro-Tech 5000VZ
      - Com-Tech
      - Note: If address 0 is selected, the IQP.I.P.DSP will operate in stand- alone mode.
      - Crown Bus Data Communication
      - Audio
      - Data Acquisition
        Page 24
  - 247 IQ Address Tables
    - Fig. 7.1 IQ Address Switch (SW1) Settings from 0 to 125
    - into a stand- alone mode where it is invisible to the
    - IQ P.I.P.DSP
      - as shown. See Section 4.1 also.
        25Page 25
        Fig. 7.2 IQ Address Switch (SW1) Settings from 126 to 250
  - 268 Service
    - 8.1 Worldwide Service
      - Internet:
      - Fax Back:
      - Facsimile:
      - Telephone:
      - Owners Manual
      - Reference
    - 8.2 North American Service
    - Crown Audio Division
      - Email:
  - 27Crown Factory Service Information
    - NATURE OF PROBLEM
      - ENCLOSE THIS PORTION WITH THE UNIT. DO NOT MAIL SEPARATELY.