Manuals / Brands / Computer Equipment / Switch / 3Com / Computer Equipment / Switch

3Com 2200 Table 11-1 describes the type of information provided for the bridge port.

1 200

Download 200 pages, 952.17 Kb

Displaying Bridge Port Information 11-3

Table 11-1 describes the type of information provided for the bridge port.

Table 11-1 Bridge Port Attributes

Parameter Description

designatedBridge Identification of the designated bridge of the LAN to which the

port is attached

designatedCost Cost through this port to get to the root bridge. The designated

cost of the root port is the same as the cost received in incoming

BPDUs from the designated bridge for that LAN.

designatedPort Identification of the designated port on the designated bridge

designatedRoot Identification of the bridge designated as root

fwdTransitions Number of times the port has entered forwarding state. This value

is useful for checking the stability of a bridged topology. The

more transitions in and out of the forwarding state, the more

unstable is the topology.

pathCost Cost to be added to the total path cost when this port is the root

port

port Either Ethernet or FDDI (maximum count: 1 = FDDI

and 2 –17 = Ethernet)

portId Identification of the port, which includes the port priority and the

port number (for example: 8002)

priority First factor to determine if a port is to be the designated port

when more that one bridge port is attached to the same LAN. If

all ports in a bridge have the same priority, then the port number

is used as the determining factor.

rxAllFilters Number of frames discarded because of a user-defined packet

filter on the receive all path of this bridge port

rxBlockedDiscs Number of frames discarded by this port because the receiving

bridge port was not in the forwarding state

rxDiscards Total number of received frames discarded (summary report only)

rxErrorDiscs Number of frames discarded by this port because of internal

bridge system errors (such as hardware and software address

table discrepancies)

rxFloodUcasts Number of unicast frames received on this port that were flooded

to one or more ports

rxForwardMcasts Number of multicast frames received on this bridge port

rxForwardUcasts Number of unicast frames received on this bridge port

(continued)

Contents

Main 3Com Corporation 95052-8145 Santa Clara, California 5400 Bayfront Plaza C ONTENTS II II S -L F III E FDDI P IV B P Page 13 PART APPENDIXES A B I ABOUT THIS GUIDE How to Use This Guide Switch 2200. The parts of the guide are described in Table 1. Conventions this guide. Switch 2200 Documentation Documentation Comments Page S UPER Conguration Tasks VERVIEW O S WITCH TACK II S 2200 A Page Page Page Page Page Page 2 A Initial User Access Levels of User Access Page Using Menus to Perform Tasks Page Page 2-6 CHAPTER 2: HOW TO USE THE ADMINISTRATION CONSOLE Figure 2-4 Bridging Menu Hierarchy for Administer Access Figure 2-5 IP Menu Hierarchy for Administer Access Page Page Page Administration Console Interface Remote Access Parameters Page Running Scripts of Administration Console Tasks Page Page Getting Help in the Administration Exiting the Administration Page Page 3 ACCESS TO THE SYSTEM About Management Access Setting Up the Console Serial Port Setting Up an IP Interface for Management Page Page Page Page Page Page Page Page Page Page Displaying IP Statistics The IP statistics you can view are described in Table 3-3. To display IP statistics, enter the following from the top level of the Administration Console: Statistics are displayed, as shown in this example: Setting Up SNMP on Y our System Page Here is an example display of the SNMP trap reporting information: Page Page Page 4 E Displaying the System Conguration Setting Passwords Setting the System Name Changing the Date and Time Rebooting the System 5 About Setting Baselines Displaying the Current Baseline 5-2 CHAPTER 5: BASELINING STATISTICS Setting Baselines system baseline set A message similar to the following appears: Baseline set at 08/07/96 10:42:52 AM. Baselining is automatically enabled when a baseline is set. 6 R About Working with Nonvolatile Data Saving NV Data Restoring NV Data Page Examining a Saved NV Data File Resetting NV Data to Defaults Page Page 7 P Displaying Ethernet Port 7-2 CHAPTER 7: ADMINISTERING ETHERNET PORTS An example of a summary display for Ethernet ports is shown here: Table 7-1 describes the information provided about an Ethernet port. Page Page Ethernet port. However, frames may be discarded for the following reasons: Figure 7-1 shows the order in which these discard tests are made. = Figure 7-1 How Frame Processing Affects Ethernet Receive Frame Statistics = Labeling a Port Setting the Port Sta te 8 R Administering FDDI Stations Table 8-1 describes these statistics. Page To set the connection policies of an FDDI station: Page Administering FDDI Paths Page Page Administering FDDI MACs Page Administering FDDI MACs 8-11 The following example shows the detail display of FDDI MAC information: Table 8-4 describes the information provided for the FDDI MAC. Page MAC. However, a frame might be discarded for the following reasons: Page Page Page Page Administering FDDI Ports Table 8-5 describes the type of information provided for an FDDI port. Page Page Page 9 R About Roving Analysis Displaying the Roving Analysis Conguration Adding an Analyzer Port Removing an Analyzer Port Starting Port Monitoring Stopping Port Monitoring Page 10 Displaying Bridge 10-2 CHAPTER 10: ADMINISTERING THE BRIDGE The following example shows a display of bridge information. Each item in the bridge parameter list is described in Table 10-1. Page Page Enabling and Disabling IP Fragmentation Enabling and Disabling IPX Snap Translation Setting the Address Threshold Setting the Aging Time Administering STP Bridge Page Page Page 11 Displaying Bridge Port 11-2 CHAPTER 11: ADMINISTERING BRIDGE PORTS The following example shows a bridge port summary display. The following example shows a bridge port detail display. Table 11-1 describes the type of information provided for the bridge port. Page Page Page Setting the Multicast Limit Administering STP Bridge Port Page Page Administering Port Addresses 11-11 Administering Port Addresses bridge port address list Page Page 11-14 CHAPTER 11: ADMINISTERING BRIDGE PORTS To freeze all dynamic addresses: bridge port address freeze 12 P About Packet Filtering Listing Packet Filters The listing of packet lters is displayed. An example of the output follows: Displaying Packet Filters Creating Packet Filters Page Table 12-2 describes the instructions and stacks of a packet lter. 12-6 CHAPTER 12: CREATING AND USING PACKET FILTERS Figure 12-1 Ethernet and FDDI Packet Fields Page Page Page Page Page Page Creating Packet Filters 12-13 The pseudocode translates into the following packet lter: Page Page Page Page Page Page Deleting Packet Filters Editing, Checking and Saving Packet Filters Page Loading Packet Filters Assigning Packet Filters to Ports Page Unassigning Packet Filters from Ports 13 PORT GROUPS TO USE IN P Using Groups in Packet Filters Listing Groups Displaying Groups Creating New Groups Page Deleting Groups Adding Addresses and Ports to Groups Page Removing Addresses or Ports from a Group Page Loading Groups Page Page A EXAMPLES, AND SYNTAX ERRORS Page Page Page Page Page Page Page Packet Filter Examples Page Page A-12 APPENDIX A: PACKET FILTER OPCODES, EXAMPLES, AND SYNTAX ERRORS Address Group Filter This lter accepts only frames whose source and destination address are in the same group. Common Syntax Errors errors. The syntax errors and their causes are listed in Table A-1. Page B Online Technical Services Page Support from Your Network Supplier Support from 3Com Returning Products for Repair I Numerics A B C D E F G H I L M N O P R S T U V W X