Manuals / 3M / Computer Equipment / Computer Monitor

3M M2256PW manual

Models: M2256PW

1 41

Page 20

20	3M™ Multi-touch Display M2256PW User Guide

If you are using 3M™ MicroTouch™ MT 7 Software, launch the MT 7 Control Panel and follow the instructions on the Main tab. You'll be asked to touch 3 targets.

If you are writing your own drivers, you should provide your own video alignment tool.

Use the Paint program (Start> Programs> Accessories> Paint) to determine if you have multitouch operation. Retest the accuracy after you perform a calibration.

3M Touch Systems, Inc. Proprietary Information – 37531 Rev D

Page 20

Image 20

Contents

3M Touch Systems, Inc. Proprietary Information - 37531 Rev D 3M Multi-touch Display M2256PW User Guide Document Title 3M Multi-touch Display M2256PW User GuideContents Appendix A 3M PX USB Controller CommunicationsAppendix B 3M PX Serial Controller CommunicationsImportant Safety Information IntroductionOverview CHAPTERExplanation of Signal Word Consequences DANGERImportant Notes Maintaining Your Touch DisplayTouch Sensor Care and Cleaning 3M Touch Systems Support ServicesContact 3M Touch Systems CHAPTER Setting up Your M2256PW Multi-touch DisplaySystem Requirements Unpacking Your Touch Display Cables Included with Your M2256PW Multi-touch DisplayArm Mounting Option Connecting the Touch DisplayTesting the M2256PW Multi-touch Display Using the Standard Controls for the Video Card Video Card RequirementsSupported Video Display Modes and Refresh Rates Table 1. Applicable Display Mode and Refresh RateConfiguring the Display Settings Multimedia FeaturesAccess to the Video Controls Menu/Select Down Up Auto/Exit Power LEDDescription Adjusting the M2256PW Video DisplayChoices CONTRAST TOOLS Choices are OSD Timing, OSD Horizontal, OSD VerticalOSD TIMING choices are Recall, Sharpness, or ExitEnabling Your M2256PW Multi-touch Display Windows 7 USB CompatibilityAll Other Platforms Multitouch Application SupportInstalling 3M MicroTouch Software Video AlignmentIf you are using 3M MicroTouch MT 7 Software, launch the MT 7 Control Panel and follow the instructions on the Main tab. Youll be asked to touch 3 targets 3M PX USB Controller Communications Overview of USB Firmware CommunicationsCommunication Basics APPENDIX ACommand Set Set Feature - CalibrationReceiving Reports from the Controller HID Class RequestsDetermining Target Areas Upper Right Calibration Target Get Feature - GetStatusLower Left Calibration Target Get Feature - GetMaxCount Set Feature - Reset Asynchronous Reports Set Feature -Restore DefaultsCoordinate Data - MultiTouch Digitizer mode Async Report Size APPENDIX B Overview of Firmware Commands3M PX Serial Controller Communications Controller Default Settings Operating ModeCommunicating with the Controller Communication ParametersSending Commands to the Controller Receiving Responses from the ControllerFirmware Commands Controller InitializationCalibrate Table 17. Firmware Commands for PX Serial Controller DevelopmentDetermining Target Areas Guidelines for Calibrate CommandCalibrate Procedure Mode Down Up Mode InactiveMode Stream Get CopyrightName Command Null CommandSoft Reset Output IdentityRestore Defaults Unit Type= Two ASCII characters that identify the controller type Defaultcan be set to 1 or 0, where 1 = an error and 0 = no error. So a Touch Data Format= Two ASCII characters that provide status information about the controller hardware. The two characters represent one byte. EachData Sequence BitsAPPENDIX C Regulatory InformationRegulatory Agency Approvals 3M Multi-touch Display M2256PW User Guide FCC WarningCE Conformity for Europe

￿If you are using 3M™ MicroTouch™ MT 7 Software, launch the MT 7 Control Panel and follow the instructions on the Main tab. You'll be asked to touch 3 targets.

If you are using 3M™ MicroTouch™ MT 7 Software, launch the MT 7 Control Panel and follow the instructions on the Main tab. You'll be asked to touch 3 targets.