Installing a D3LX RMT Module in a Remote Cabinet | |
|
|
3Locate the mounting slots designated for the D3LX RMT modules in the chassis. If protection switching is required, a working module installs in the first slot of a quad group, such as
4Refer to Figure 9 for D3LX RMT module locations chassis and slot corresponding to the DS3 signal.
–If no protection switching is required, proceed to the next step.
–If protection switching is required, a working module may be installed in the first slot of any quad group, such as
Install the working module first, then the protect module.
5Remove a new module from its protective ESD packaging. If the module is installed, remove it and inspect for physical damage.
6Align the module with the slot and slide the module into the chassis until about three inches protrude from the front of the chassis. Do not seat module in connector at this time.
7Remove the protective dust cap from the connector on the D3LX RMT module.
Fiber clip | Fiber patch cord |
|
|
| Fiber guides |
|
|
|
| Fiber clip | ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| TX | |
|
|
|
|
|
|
|
|
|
| A |
|
|
|
| RX | |
|
|
|
|
|
|
|
| D3RCAMS3 | P |
|
|
|
|
|
| |
|
| D3LX RMT |
| D3LX RMT |
|
|
| U | D3LX RMT | D3LX RMT |
|
| ||||
AC/DC | AC/DC |
|
| STATUS |
|
|
| |||||||||
|
|
|
|
|
|
|
| CR |
|
|
|
|
|
| ||
|
| STATUS |
|
| STATUS |
|
| ENABLE | STATUS |
| STATUS |
|
| |||
|
|
|
|
|
|
|
|
|
| |||||||
|
| FAR END |
|
| FAR END |
|
| APS |
| MJ | FAR END |
| FAR END |
| TX | RX |
|
|
|
|
| C | FAIL | NET |
|
|
| ||||||
|
|
|
|
|
|
| ERROR |
|
|
|
|
|
|
| ||
|
| DS3 STATUS |
| DS3 STATUS | R | FAIL | EOP | MN | DS3 STATUS | DS3 STATUS |
|
| ||||
|
|
| A |
|
| |||||||||||
|
|
| ERROR |
|
|
|
| |||||||||
|
|
| R=FAULT |
|
| R=FAULT | F |
|
|
|
| R=FAULT |
| R=FAULT |
|
|
|
| ENABLE | G=O.K. |
| ENABLE | G=O.K. | T |
|
|
| ENABLE | G=O.K. | ENABLE | G=O.K. |
|
|
|
| FLASH=LBK |
| FLASH=LBK |
|
|
|
| FLASH=LBK | FLASH=LBK |
| |||||
|
|
| OFF=UNEQPP |
|
| OFF=UNEQPP |
|
|
|
| OFF=UNEQPP |
| OFF=UNEQPP |
| ||
|
|
|
|
|
|
|
|
|
| ACO |
|
|
|
|
| |
|
| DS3 ONLINE |
| DS3 ONLINE |
| CRAFT |
| DS3 ONLINE | DS3 ONLINE | TX | RX | |||||
|
| FAIL | G=ONLINE |
| FAIL | G=ONLINE |
|
|
| PWR | FAIL | G=ONLINE | FAIL | G=ONLINE | ||
| OPT | OFF=OFFLINE | OPT | OFF=OFFLINE |
|
| R=LINELOCK | R=LINELOCK |
|
| ||||||
POWER | POWER | BER |
|
| BER |
|
|
|
| OPT | BER | OFF=OFFLINE OPT | BER | OFF=OFFLINE |
|
|
LOCKOUT |
|
| LOCKOUT |
|
|
|
| HSKP APS | LOCKOUT |
| LOCKOUT |
|
|
| ||
| APS |
| APS |
|
| RESET | APS |
|
|
| ||||||
|
| FORCE |
|
| FORCE |
|
| APS/LMP TST |
| FORCE |
| FORCE |
|
|
| |
|
| LMPTST/ |
|
| LMPTST/ |
|
|
|
| RMT | LMPTST/ |
| LMPTST/ |
|
| |
|
|
|
|
|
|
|
| ALM |
|
| TX | |||||
|
| APS |
|
| APS |
|
|
|
|
| APS |
| APS |
| ||
|
| RESET |
|
| RESET |
|
|
|
| DISP RMT | RESET |
| RESET |
|
|
|
|
|
|
|
|
|
|
|
|
| LMPTST |
|
|
|
|
|
|
Fiber |
|
|
|
| D3RCAM |
|
|
|
|
| ||||||
management |
|
|
|
|
|
|
|
| APU |
|
|
|
| D3LX LTU | ||
enclosure |
|
|
|
|
| D3LX RMT modules |
|
|
| jack block | ||||||
Figure 9. D3LX RMT Module Locations in a
8After removing the protective cover from a fiber patch cord, confirm that the
9Proceed to “Power Verification” on page 16.
D3LX CO and RMT Modules | August 30, 2002 | 15 |