Carrier Frequency | Agilent Technologies U2761A instruction

Features and Functions

2

Remote Interface Operation

FUNCtion {SINusoidSQUareRAMPUSER}

You can also use the APPLy command to select the function, frequency, amplitude, and offset.

Carrier Frequency

The maximum carrier frequency depends on the function selected as shown below. The default carrier frequency is 1 kHz for all functions.

Table 2-5Carrier frequency for PM

Function	Minimum frequency	Maximum frequency

Sine	1 μHz	20 MHz

Square	1 μHz	20 MHz

Ramp, Triangle	1 μHz	200 kHz

Arbitrary	1 μHz	200 kHz

Soft Front Panel Operation

On the Frequency panel as shown in Figure 2- 3, input the desired frequency value and select the unit from the drop down list.

Remote Interface Operation

FREQuency <frequency>

You can also use the APPLy command to select the function, frequency, amplitude, and offset.

U2761A User’s Guide

63

Image 81

Agilent Technologies U2761A manual Carrier Frequency, 5Carrier frequency for PM

Contents

User’s Guide U T I O N WA R N I N G Safety Symbols Instrument Use the device with the cables providedPerformed by qualified personnels Environment Conditions Regulatory Markings Affixed product label is shown as below Product Category Declaration of Conformity Regulatory Information for Australia/New Zealand This Guide… Contents Output Control Sweep Time Index List of Figures Trigger output pulse List of Tables Xviii Getting Started Introduction Various features of the U2761A Product Outlook Product at a GlanceTop View Bumpers Power inlet Fan Ventilation Pin backplane connector USB inletFront View Rear View Dimensions Without Bumpers Product Dimensions105.00 mm 175.00 mm 18.00 mm 25.00 mm Dimensions With Bumpers 117.00 mm 180.00 mm 15.00 mm41.00 mm Standard Purchase Items General Maintenance Inspection and MaintenanceInitial Inspection Electrical Check Installation and Configuration InstallationWith Agilent VEE Pro, LabVIEW, or Microsoft Visual Studio Hard-disk space 1 GB Check Your System Install the IO Libraries Suite Install the Module Driver Install the Agilent Measurement Manager T E Proceeding Connect the Module to Your PC Getting Started Go to Start Control Panel and double-clickSystem Select Ignore to disable the warning message Getting Started Verify Your Module Connection Send Commands To This Instrument Launch Your Agilent Measurement Manager IO Control will launch automatically when you start your PC T E Description Pin Backplane Connector Pin Configuration Chassis Installation Triggering Pulse Waveform Introduction Output ConfigurationOutput Function 1Output functions Amplitude Limitation Function Limitation Waveform pattern selection Waveform parameters Soft Front Panel Operation Output Frequency Remote Interface Operation2Output frequency range Duty Cycle Limitations Function Limitations Output Amplitude Offset Voltage LimitationsLimits Due to Output Termination 4Panel view of the amplitude section Limits Due to Units Selection Limits Due to Amplitude DC Offset Voltage VOLTageOFFSet offset Output Units Output Termination OUTPutLOAD ohmsINFinity Duty Cycle Square Waves Duty CycleLimits Due to Frequency APPLy command automatically sets the duty cycle to 50% 9Ramp wave duty cycles Symmetry Ramp Wave 11Panel view of the output section Output Control Example 1, To output a DC voltage Set Output Using Scpi Commands Example 2, To output a Sine wave Example 4, To output a Ramp wave Pulse Period Pulse Waveform 13Panel view of the pulse width section Pulse Width Duty Cycle = 100 ⋅ Pulse Width / Period Pulse Duty Cycle Example Generate Pulse Waveform Using Scpi Commands Amplitude Modulation AM To Select AMModulating frequency AM depth 15Panel view of AM Carrier Waveform 3Carrier frequency for AM Carrier Frequency Modulating Waveform Default modulating waveform is Sine wave Modulating Waveform Frequency Modulation DepthPeak into a 50 Ω load Generate AM Using Scpi Commands Frequency Modulation FM To Select FMModulating frequency FM deviation FMSTATe 0OFF1ON 4Carrier frequency for FM FMINTernalFUNCtion SINusoidSQUareRAMPNRAMpTRIangleUSER Frequency Deviation Generate FM Using Scpi Commands Phase Modulation PM Modulating frequency Phase deviationTo Select PM PMSTATe 0OFF1ON 5Carrier frequency for PM Default waveform is Sine wave Generate PM Using Scpi Commands Phase Deviation Frequency-Shift Keying FSK Modulation To Select FSK ModulationFSK rate Hop frequency FSKeySTATe 0OFF1ON 6Carrier frequency for FSK FSK Carrier Frequency 7Hop frequency FSK Hop Frequency FSK Rate Generate FSK Modulation Using Scpi Commands Phase-Shift Keying PSK Modulation To Select PSK ModulationPSK rate PSK deviation PSKeySTATe 0OFF1ON 8Carrier frequency for PSK PSK Carrier Frequency PSK Deviation PSK Rate Generate PSK Modulation Using Scpi Commands Amplitude-Shift Keying ASK Modulation To Select ASK ModulationASK rate ASKeySTATe 0OFF1ON 9Carrier frequency for ASK ASK Rate Generate ASK Modulation Using Scpi Commands Frequency Sweep To Select SweepFrequency Linear type Start frequency Stop frequency 28Panel view of sweep Start Frequency and Stop Frequency Sweep Time Sweep Mode Sweep Trigger Source Set Frequency Sweep Using Scpi Commands Trigger Source Choices Triggering Manual Triggering Internal Triggering External Triggering Trigger Output Signal Trigger Input SignalTrigger Rising edge shown Trigger out 500 μs Rising edge shown OUTPutTRIGger 0OFF1ON OUTPutTRIGgerSLOPe POSitiveNEGative Set Triggering Using Scpi Commands To Create and Store an Arbitrary Waveform Arbitrary Waveforms Select the Arbitrary waveform function Start waveform editing process Exiting the waveform editor Characteristics and Specifications Operating Environment Product Characteristics Waveforms Product Specifications and Characteristics Ramp, Triangle External frequency reference Units Vpp, Vrms, dBm Resolution Digits±1% of settling ±5 mV ±10 mV @ Hi-Z ±5 V across open circuit Modulation Sweep Characteristics 102 U2761A User’s Guide Index PSK United States Tel 800 829