Detail control | Alcatel Carrier Internetworking Solutions TQBJ0223

Detail control page

Click [Projector control], then [Detail control] to display the Detail control page.

On-screen status is displayed, even if the on-screen of projector is set to off.

This button updates the on-screen description on the right of the control page with the latest information.

Pressing these buttons controls the projector and updates the on-screen description on the right of the control page when control is finished.

ENGLISH

Monitor information page

Click [Projector control], then [Status information] to display the Status information page. This page displays the projector statuses established for the items shown below.

Displays the input switching status.

Displays temperature of projector’s intake air.

Displays temperature inside the projector.

Displays temperature around the lamp.

Displays the lamp1 lit hours.

Displays the lamp2 lit hours.

Displays the type of projector.

Displays used hours of the projector.

Displays self-diagnosis information.

Displays the firmware version of the projector main unit.

39

Image 39

Alcatel Carrier Internetworking Solutions TQBJ0223 manual Detail control, Monitor information

Contents

Model No. PT-D4000E Commercial Use Dear Panasonic Customer Important Safety Notice Important the Moulded Plug U.K. only For Your SAFETY, Please Read the Following Text Carefully Contents Precautions with regard to safety Always disconnect all cables before moving the projector Remove empty batteries from the remote control at onceDo not use or handle the batteries improperly Do not disassemble the lamp unit Electric shocks can result if this is not done AccessoriesDo not use the old lamp unit Do not place the projector in extremely hot locations Precautions on handling Name and function of parts Remote control Bottom Status LED lights Front and side of the projector Rear view of the main unit Controls on rear panel Side-mounted connection terminals Using the remote control unit Effective range of remote control operationLoading dry cells Connect to the projector to use with a cable Setting projector ID number to remote control Unit mm InstallationInstallation geometry Projection schemes Projection distance by projection lens Screen aspect ratioScreen aspect ratio Calculation formulas for projection distance by lens types Setup precautions ConnectionPin assignments on the RGB2 input terminal are as follows Example of connecting with PCs Example of connecting with AV products When operating at the projector, please refer to Powering up the projectorMaking adjustment and selection Press the I button. on the main unit or the remote control Direct power off function Powering off the projector How to adjust the lens How to adjust the FOCUS, Zoom and ShiftHow to remove the projection lens Press the Shutter button again Automatic adjustmentPress the Status button on the remote control Status function On-screen menus For RGB signalsFor DVI signals For S-Video/Video/YPBPRsignals Returning to the previous Menu items settingResetting to the factory default Basic menu operations Adjusting the picture Adjusting the position Digital Cinema Reality Clock PhaseZoom Keystone Clamp Position Input ResolutionXGA Mode Sxga Mode OPTION1 settings OSD Position DVI Signal LevelDVI Edid FUNC1 Altitude OPTION2 settingsInstallation Projector ID Lamp Select Lamp RelayRS-232C Date and Time Auto Power OFFPassword System Information Connection example Setting the networkConnecting the PC System requirements Click Change password Using Web Browser ControlAccessing from the Web browser Password change Basic control Monitor information Detail control Error information Mail set up An error is detected by self- diagnosisOn the next Mail set up page Continuing Authentication server set upChange the authentication method as desired Ping test DNS server set up Adjust clock Contents of mail sent Network status Network config Command Control Description Remarks Using the PJLink protocolSupported commands PJLink security authentication Control Device Setup Setting the securityPassword Change Display Setting Examples of connection Using the serial terminalsPin assignments and signal names Communication conditions Factory setting Pin assignments and control Control commandsCable specifications Connecting to a PC Computer Projector DTE specifications Indication of lamp monitor Dismantle the air filter Cleaning and replacement of air filterProcedure of cleaning Clean the air filter After When to replace the Lamp unitReplacing the lamp unit Lamp Have a Phillips screwdriver ready ahead of time Lamp unit replacement stepsRemove the two screws securing the fan unit Lamp unit will be hot after it has been used Installation procedure Ceiling Mount Bracket Safeguards Image is blurred Power doesNot turn on No image PT-D4000E Specifications Replacement lamp unit Length of power cord CabinetOutside dimensions Remote control Power source PAL-M/PAL60 PAL/PAL-N/SECAM Compatible Signal List Dimensions Installation dimensions diagramUnit mm Trademark Acknowledgement For business users in the European Union