Alto-Shaam 750-TH-II manual D A N G E R, I N S T A L L A T I O N, Applicable Electrical Codes

I N S T A L L A T I O N

E L E C T R I C A L C O N N E C T I O N

The appliance must be installed by a qualified service technician. The oven must be properly grounded in accordance with the National Electrical Code and applicable local codes.

Plug the unit into a properly grounded receptacle ONLY, positioning the unit so that the plug is easily accessible in case of an emergency. Arcing will occur when connecting or disconnecting the unit unless all controls are in the “OFF” position.

Proper receptacle or outlet configuration or permanent wiring for this unit must be installed by a licensed electrician in accordance with applicable local electrical codes.

750- and 1000-TH-II models at 208-240V are dual rated units with a conversion switch mounted under an access cover on the rear of the oven, near the power cord.

With the voltage conversion switch in the 200-208V (UPPER) position, the oven will function properly with a source voltage of between 200 and 208. With the voltage conversion switch in the 220-240V (LOWER) position, the unit will function properly with a source voltage of between 220 and 240.

ALL 208-240V units are shipped from the NOTE: factory with the voltage conversion switch

in the 220-240 position.

All 125V rated units will function properly with a source voltage of between 100 and 125, 60 Hz.

E L E C T R I C A L - 5 0 0 - T H - I I
VOLTAGE	PHASE	CYCLE/ HZ	AMPS	kW		CORD & PLUG
120	1	60	16	1.92		NEMA 5-20P
208-240 (AGCY) 1		60	12.5	3.0		20A - 125V PLUG
						NO CORD
at 208	1	60	10.6	2.2	&		PLUG
at 240	1	60	12.2	2.93
230	1	50	12	2.75		CEE 7/7
						220-230V PLUG
E L E C T R I C A L - 7 5 0 - T H - I I
VOLTAGE	PHASE	CYCLE/ HZ	AMPS	kW		CORD & PLUG
120	1	60	14.2	1.7		NEMA 5-20P
208-240 (AGCY) 1		60	14.4	3.0		20A - 125V PLUG
						NO CORD
at 208	1	60	14.6	3.0	&		PLUG
at 240	1	60	11.2	2.7
230	1	50	10.4	2.4		CEE 7/7
						220-230V PLUG
ELECTRICAL - 1000-TH-II, -II-SPLIT (EACH COMPARTMENT)
VOLTAGE	PHASE	CYCLE/ HZ	AMPS	kW		CORD & PLUG
120	1	60	16.0	1.92		NEMA 5-20P
208-240 (AGCY) 1		60	14.4	3.0		20A - 125V PLUG
						NO CORD
at 208	1	60	14.4	3.0		& PLUG
at 240	1	60	11.1	2.7
230	1	50	10.4	2.4		CEE 7/7
						220-230V PLUG

The 125V rated units are provided with a cord and plug [NEMA #5-20P]. Have a licensed electrician install the proper outlet configuration as required for the unit in accordance with applicable, local electrical codes. This will assure a safe and trouble-free installation.

Ensure that the voltage conversion switch position

and the available power source match.

To prevent an electrical shock hazard between 230V:the appliance and other appliances or metal parts

in close vicinity, an equalization-bonding stud is provided. An equalization bonding lead must be connected to this stud and the other appliances / metal parts to provide sufficient protection against potential difference. The terminal is marked with the following symbol.

230V appliances must be connected to NOTE: an electrical circuit that is protected by

an external GFCI outlet.

D A N G E R

ENSURE POWER SOURCE

MATCHES VOLTAGE STAMPED

ON APPLIANCE NAMEPLATE.

D A N G E R

APPLIANCES WITH NO CORD

PROVIDED BY FACTORY MUST BE

EQUIPPED WITH A CORD OF

SUFFICIENT LENGTH TO PERMIT

THE APPLIANCE TO BE MOVED

FOR CLEANING.

ELECTRICAL CONNECTIONS MUST

BE MADE BY A QUALIFIED SERVICE

TECHNICIAN IN ACCORDANCE WITH

APPLICABLE ELECTRICAL CODES.

D A N G E R

To avoid electrical shock, this appliance MUST be adequately grounded in accordance with local electrical codes or, in the absence of local codes, with the current edition of the National Electrical Code ANSI/NFPA No. 70. In Canada, all electrical connections are to be made in according with CSA C22.1, Canadian Electrical Code Part 1 or local codes.

TH-IIINSTALLATION/OPERATION/SERVICE MANUAL PG. 11