Alto-Shaam AR-7E manual Sta Ck Ing, Com Bin At Ions, Insta Llat Ion, Re Qu Irements, C Au Tio N

INS TAL LAT ION

STA CK ING	COM BIN AT IONS	& INSTA LLAT ION	RE QU IREMENTS
STACKING	CO MB IN ATION S (FACTORY INSTALLED)
AR-7Erotisser ie over AR- 7E rotiss erie			and sta cking assembly (5009981,
Requires 6" (152mm) leg asse mbly 500 1414 or 5" (127 mm) casters 4007
5009982, 5009983, 5010355, 5010356, or 5010357 - dep ending on voltag e and door swin g - see pg 8) for
app lic atio ns withi n the Unite d Sta tes.		Appl ications outside the U.S. requires 6" (152 mm) legs wit h
fla nged feet 5001761 bolte d to the floo r.
[OVERA LL HEI GHT : 76-7/8" (1953mm)]
AR-7Erotisser ie ove r AR-7 H companion holding cabinet			and stac kin g assem bly (50087 87,
Requir es 6" (152mm) leg ass embly 5001414 or 5" (127 mm) caste rs 4007

5008948 or 5008922 - depen ding on voltage - see pg 8) for applica tion s within the United Sta tes. Applica tio ns outside the U.S . requires 6" (152mm) legs with fla nged feet 500 1761 bolted to the floor. [OVERA LL HEI GHT : 76-7/8" (1953mm)]

CAUTION

STACKING APPLICATIONS

OUTSIDE THE U.S. REQUIRE

FLANGED FEET AND MUST

BE BOLTEDTOTHE FLOOR.

STA CK ING IN STRU CTION S

A rotisserie can be stacked with another rotisserie or can be stacked on top of a matching holding cabinet.

Stacking hardware is required for all stacking combinations

(SEE ABOVE AND THE OPTIONS LIST ON PG 8 FOR MORE INFORMATION).

All fastening holes have been prepunched. The stacking combination also requires the minimum clearance of 6" (152mm) at the top, back and both sides.

NOT E: Do note remove corner panels. They are not shown in the drawing only to increase visibility of the interior components.

1. Remove the access panels of both units.

2. 208-240V, 1PH - RH/LH DOOR SWING :

Remove power cord, strain relief bushing, and strain relief washer (drill out 2 rivets) from the rotisserie intended to be on the top. Discard power cord.

208-240V, 3PH - RH/LH DOOR SWING:

Remove power cord and strain relief bushing from the rotisserie intended to be on the top. Discard power cord.

380-415V - RH/LH DOOR SWING:

Remove strain relief bushing from the rotisserie intended to be on the top.

C AU TIO N

MAKE CERTAINTO FASTEN

EACH OF THE FOUR HOLES

3.Attach cover plate (1010464) to cord hole with 2 rivets.

4.Remove any existing legs or casters from both of the rotisseries.

5.Review “stacking combinations & installation requirements” above, then attach support brackets and legs or casters to the rotisseries intended to be on the bottom with 1" (25mm) screws, washers, and lock washers.

6.Punch out the knock out holes A, B, C, & D.

7.Detach decorative exhaust by removing 6 screws from top panel of rotisserie intended to be on the bottom.

8.Remove 4 plugs (E) from top panel of rotisserie intended to be on the bottom.

9.Apply high temp silicone around perimeter of exhaust opening on the top panel of the rotisserie to be on bottom (F).

10.Carefully lift and place the upper unit into position aligning on the bottom unit.

11.Secure units together by inserting a hex head screw and a flat washer in each hold of the top unit and a flat washer, lock washer, and hex nut inside the bottom unit. Securely tighten all four screws.

AR- 7E Roti ss eri e Operat ion & Care Manual • 6