Manuals / Alto-Shaam / Kitchen Appliance / Oven

Alto-Shaam Combination Oven/Steamer manual Mobile Equipment Restraint, Risk Of Electric Shock

Models: Combination Oven/Steamer

1 31

Download 31 pages 30.01 Kb

Page 15

MOBILE EQUIPMENT RESTRAINT

I N S T A L L A T I O N

MOBILE EQUIPMENT RESTRAINT

Any appliance that is not furnished with a power supply cord but includes a set of casters, stand with casters, or a stacked configuration must be installed with a tether. Adequate means must be provided to limit the movement of this appliance without depending on or transmitting stress to the electrical conduit. The following requirements apply:

1.Casters must be a maximum height of 6" (152mm).

2.Two of the casters must be the locking type.

3.Such appliances must be installed with the use of a flexible connector secured to the building structure.

4.Each of the stacked appliances must be installed with the use of a flexible connector secured to the building structure. A single wall anchor may be used.

A mounting connector for a restraining device is located on the top right back panel of the appliance chassis or on an oven stand, approximately

18" (457mm) from the floor. A flexible connector is not supplied by nor is it available from the factory.

WARNING

RISK OF ELECTRIC SHOCK.

Appliance must be secured

to building structure.

Mounting connector for restraining device

CT EXPRESS SERIES • INSTALLATION MANUAL • MN-29805 • 13..

Image 15

Alto-Shaam Combination Oven/Steamer manual Mobile Equipment Restraint, Risk Of Electric Shock, I N S T A L L A T I O N

Contents

410ESiVH INSTALLATIONCT EXPRESS 410ESiWarranty InstallationSee Transportation Damage and Claims section located in this manual C A U T I O ND E L I V E R Y U N P A C K I N GN O T E SAFETY PROCEDURES AND PRECAUTIONSD A N G E R W A R N I N GVENTILATION REQUIREMENTS SITE INSTALLATIONINSTALLATION CODES & STANDARDS I N S T A L L A T I O Ni n s t a l l a t i o n site INSTALLATIONc a u t i o n dangerLIFTING INSTRUCTIONS C A U T I O NI N S T A L L A T I O N I N S T A L L A T I O N Stand InstallationPOSITIONING REQUIREMENTS SITE INSTALLATIONI N S T A L L A T I O N ACCESSORIESWEIGHT 410esiINSTALLATION REQUIREMENTS DIMENSIONS H x W x D23-3/4 410esiVH52-3/16 1325mm 37-13/16 960mm 39-1/2 1003mmWEIGHT 410cciINSTALLATION REQUIREMENTS DIMENSIONS H x W x D EXTERIORON APPLIANCE RATING TAG ENSURE POWER SOURCE MATCHES VOLTAGE IDENTIFIEDDANGER ELECTRICAL CONNECTIONI N S T A L L A T I O N Top/Back of unitDANGER DANGERMOBILE EQUIPMENT RESTRAINT RISK OF ELECTRIC SHOCKI N S T A L L A T I O N VERIFY WATER SUPPLY BEFORE STARTING CLEANING PROGRAM WATER QUALITY REQUIREMENTALTO-SHAAM COMBITHERM WATER QUALITY MINIMUM STANDARDS WATER SUPPLY MUST BE OPEN WHEN CLEANING PROGRAM IS ACTIVATEDIS NEEDED REFER TO FIGURE 1 ABOVE FOR PROPER INTAKE LOCATIONS WATER CONNECTIONSONE SUGGESTED METHOD OF INSTALLATION I N S T A L L A T I O NINSTALLATION OPTIONAL HAND HELD SPRAY HOSEI N S T A L L A T I O N I N S T A L L A T I O N WATER VALVEWATER DRAINAGE WHEN THE OVEN IS BEING USEDVENTLESS HOOD MODEL OPERATIONI N S T A L L A T I O N TOP EXHAUST VENT FILTER SWITCHI N S T A L L A T I O N VENTLESS HOOD MODELPage PHASE INSTALLATIONCT EXPRESS CHECKLIST Verify electrical power requirements for ovenPage PRESS THE START ICON TO ACKNOWLEDGE THE ERROR ERROR CODESbe shown in the error code list and ERROR CODESError E20 is not shown in display the customer cooks in time modeERROR CODES ERROR CODES PRESS THE START ICON TO ACKNOWLEDGE THE ERROR ERROR CODESORIGINAL EQUIPMENT LIMITED WARRANTY THIS WARRANTY DOES NOT APPLY TOALTO-SHAAM COMBITHERM WATER QUALITY MINIMUM STANDARDS TRANSPORTATION DAMAGE AND CLAIMS Model Serial Number Date Installed Voltage Purchased FromDriver refuses to allow inspection of containers for visible damage