Manuals / Alto-Shaam / Kitchen Appliance / Oven

Alto-Shaam Combination Oven/Steamer manual Optional Hand Held Spray Hose, Installation

Models: Combination Oven/Steamer

1 31

Download 31 pages 30.01 Kb

Page 18

Image 18

I N S T A L L A T I O N

OPTIONAL HAND HELD SPRAY HOSE

Sprayer hanger

Sprayer hose

Valve

Valve bracket

INSTALLATION

1.Two pre-drilled holes with screws in place are located at the lower rear side of the unit (same side as door opening). Remove screws, position valve bracket and attach using the 2 self drilling screws.

2.Three pre-drilled holes with screws in place are located at the upper front side of unit (same side as door opening). Remove screws, position sprayer hanger and fasten using the 3 self-drilling screws.

3.Connect the sprayer hose to the valve and place the sprayer in the hanger.

4.Continue to connect an incoming water supply line to the valve.

CT EXPRESS SERIES • INSTALLATION MANUAL • MN-29805 • 16..

Page 18

Image 18

Alto-Shaam Combination Oven/Steamer manual Optional Hand Held Spray Hose, Installation, I N S T A L L A T I O N

Contents

410ESi INSTALLATIONCT EXPRESS 410ESiVHInstallation WarrantyU N P A C K I N G C A U T I O ND E L I V E R Y See Transportation Damage and Claims section located in this manualW A R N I N G SAFETY PROCEDURES AND PRECAUTIONSD A N G E R N O T EI N S T A L L A T I O N SITE INSTALLATIONINSTALLATION CODES & STANDARDS VENTILATION REQUIREMENTSdanger site INSTALLATIONc a u t i o n i n s t a l l a t i o nLIFTING INSTRUCTIONS C A U T I O NI N S T A L L A T I O N SITE INSTALLATION Stand InstallationPOSITIONING REQUIREMENTS I N S T A L L A T I O NACCESSORIES I N S T A L L A T I O NDIMENSIONS H x W x D 410esiINSTALLATION REQUIREMENTS WEIGHT39-1/2 1003mm 410esiVH52-3/16 1325mm 37-13/16 960mm 23-3/4DIMENSIONS H x W x D EXTERIOR 410cciINSTALLATION REQUIREMENTS WEIGHTELECTRICAL CONNECTION ENSURE POWER SOURCE MATCHES VOLTAGE IDENTIFIEDDANGER ON APPLIANCE RATING TAGDANGER Top/Back of unitDANGER I N S T A L L A T I O NMOBILE EQUIPMENT RESTRAINT RISK OF ELECTRIC SHOCKI N S T A L L A T I O N WATER SUPPLY MUST BE OPEN WHEN CLEANING PROGRAM IS ACTIVATED WATER QUALITY REQUIREMENTALTO-SHAAM COMBITHERM WATER QUALITY MINIMUM STANDARDS VERIFY WATER SUPPLY BEFORE STARTING CLEANING PROGRAMI N S T A L L A T I O N WATER CONNECTIONSONE SUGGESTED METHOD OF INSTALLATION IS NEEDED REFER TO FIGURE 1 ABOVE FOR PROPER INTAKE LOCATIONSINSTALLATION OPTIONAL HAND HELD SPRAY HOSEI N S T A L L A T I O N WHEN THE OVEN IS BEING USED WATER VALVEWATER DRAINAGE I N S T A L L A T I O NVENTLESS HOOD MODEL OPERATIONI N S T A L L A T I O N VENTLESS HOOD MODEL FILTER SWITCHI N S T A L L A T I O N TOP EXHAUST VENTPage Verify electrical power requirements for oven INSTALLATIONCT EXPRESS CHECKLIST PHASEPage ERROR CODES PRESS THE START ICON TO ACKNOWLEDGE THE ERRORthe customer cooks in time mode ERROR CODESError E20 is not shown in display be shown in the error code list andERROR CODES ERROR CODES ERROR CODES PRESS THE START ICON TO ACKNOWLEDGE THE ERRORORIGINAL EQUIPMENT LIMITED WARRANTY THIS WARRANTY DOES NOT APPLY TOALTO-SHAAM COMBITHERM WATER QUALITY MINIMUM STANDARDS TRANSPORTATION DAMAGE AND CLAIMS Model Serial Number Date Installed Voltage Purchased FromDriver refuses to allow inspection of containers for visible damage