American Power Conversion 3000, 5000 - page 14

11

3Battery Pack coupler

Battery Packs are connected at this coupler. A coupler clamp is installed over the

coupler opening as furnished from the factory. See the Installation section for

instructions on how to lock mated couplers.

4Accessory panel

The EU is furnished with an opening that accepts accessories that work with the UPS.

Call your dealer or the factory for information on available accessories.

5Computer interface port

See the UPS Monitoring section of this manual for information on this interface port.

6Battery communications jack

The Battery Pack communications cable from the Battery Pack OUTPUT is connected

at this jack.

7Manual bypass switch

Pressing the manual bypass switch causes the UPS to transfer to the bypass mode of

operation. While in this mode, the load is supplied with power conditioned by the

IU. However, the load will not be protected from mains voltage sags, swells or

blackouts. The EU is removed for service when the UPS is operating in bypass. See

the Operation section of this manual for more details on this mode of operation.

8Emergency Power Off jack

For applications where, for safety reasons, power to all room equipment must be cut

off, the UPS provides a remote Emergency Power Off interface. A modular 6 position

plug with offset latch fits this jack. See the Installation section of this manual for

instructions on how to connect to the jack.

3.0 Presentation

Contents

Main Important safety instructions! Radio frequency interference Limited Warranty Life Support Policy Table of Contents 1.0 Introduction 1.1 Overview 1.0 Introduction 1.2 Hot swappable modules 1.3 Emergency Power Off (EPO) 1.4 Display 1.5 Remote interfaces 2.0 Safety! CAUTION! 2.0 Scurit! ATTENTION! 2.0 Sicherheit! VORSICHT! 2.0 Seguridad! ATENCION! 3.1 Isolation Unit (IU) Page 3.2 Electronics Unit (EU) Page 3.3 Battery Pack Page 4.1 Receiving inspection 4.2 Protection Strategies 4.3 Moving the UPS Page 4.5 Input voltage requirements 4.5.1 208 Vac operation 4.5.2 220240 Vac operation 4.6 Installation procedures 4.6.1 Required materials 4.6.2 Required tools 4.7 Input hard wiring procedure Page 4.7 Input hard wiring procedure (continued) 4.8 Input voltage tap selection208 Vac, 50/60 Hz use only Input voltage select wire (red) 4.9 Output wiring procedure Jumper cord 4.9 Output wiring procedure (continued) 4.10 Module interconnections 4.0 Installation 4.10 Module interconnections (continued) 4.11 Emergency Power Off (EPO) interface pin 6 offset latch jack pin 1 offset latch plug N UPS Loads 5.1 Modes of operation 5.1.1 Sleep mode 5.1.2 Standby mode 5.1.3 On-line mode 5.1.4 On-battery mode 5.1.5 Bypass mode 5.1.6 Transfer between modes of operation 5.2 Display and controls operation 5.2.1 Default screens 5.2.2 Main menu screens 5.2.3 UPS Control menu 5.2.4 UPS Status menu 5.2.4 UPS Status menu (continued) 5.2.5 UPS Diagnostics menu 5.2.5 UPS Diagnostics menu (continued) 5.2.6 UPS Setup Page 5.2.6 UPS Setup (continued) 5.2.7 UPS Tests 5.2.8 Password protection 6.0 UPS Monitoring 6.1 Overview 6.2 Interface Kits 6.3 PowerChute Software 6.0 UPS Monitoring 6.4 Computer Interface port 7.0 Difficulty 7.0 Difficult 7.0 Schwierigkeit 7.0 Dificultad Page 7.2 Fault messages 7.2.1 Replace Electronics Unit (EU) 7.2.2 UPS requires service 7.3 Replacing the Electronics Unit 7.4 Replacing or adding Battery Packs 7.5 Obtaining Service 8.0 Storing the UPS 8.1 Storage conditions 8.2 Extended storage 9.0 Specifications 9.1 Input 9.2 Transfer Characteristics 9.3 Output Characteristics 9.4 Noise and surge isolation 9.0 Specifications 9.5 Battery Pack 9.6 Environment 9.7 Physical 9.8 Approvals Page Page Page Page DECLARATION OF CONFORMITY Toll free technical support: Return shipment addresses: