American Power Conversion 3000, 5000 4.10 Module interconnections

4.0 Installation

4.10 Module interconnections

Follow the instructions listed below to install and lock the battery couplers.

4.10.1 Using a phillips screwdriver, remove the battery coupler clamps from the

Electronics Unit and from all but one Battery Pack.

4.10.2 Turn the battery coupler clamp over and fasten loosely to one side.

4.10.3 Connect the battery couplers as shown in the figure below.

4.10.4 Fasten the other side of the battery coupler clamp to secure couplers.

Note: To reduce the risk of

toppling, do not stack

equipment more than 2

units high.

Removeclamp Turnclamp Matecouplers Secure clamp

Typical installation showing mated battery couplers.

Contents

Main Important safety instructions! Radio frequency interference Limited Warranty Life Support Policy Table of Contents 1.0 Introduction 1.1 Overview 1.0 Introduction 1.2 Hot swappable modules 1.3 Emergency Power Off (EPO) 1.4 Display 1.5 Remote interfaces 2.0 Safety! CAUTION! 2.0 Scurit! ATTENTION! 2.0 Sicherheit! VORSICHT! 2.0 Seguridad! ATENCION! 3.1 Isolation Unit (IU) Page 3.2 Electronics Unit (EU) Page 3.3 Battery Pack Page 4.1 Receiving inspection 4.2 Protection Strategies 4.3 Moving the UPS Page 4.5 Input voltage requirements 4.5.1 208 Vac operation 4.5.2 220240 Vac operation 4.6 Installation procedures 4.6.1 Required materials 4.6.2 Required tools 4.7 Input hard wiring procedure Page 4.7 Input hard wiring procedure (continued) 4.8 Input voltage tap selection208 Vac, 50/60 Hz use only Input voltage select wire (red) 4.9 Output wiring procedure Jumper cord 4.9 Output wiring procedure (continued) 4.10 Module interconnections 4.0 Installation 4.10 Module interconnections (continued) 4.11 Emergency Power Off (EPO) interface pin 6 offset latch jack pin 1 offset latch plug N UPS Loads 5.1 Modes of operation 5.1.1 Sleep mode 5.1.2 Standby mode 5.1.3 On-line mode 5.1.4 On-battery mode 5.1.5 Bypass mode 5.1.6 Transfer between modes of operation 5.2 Display and controls operation 5.2.1 Default screens 5.2.2 Main menu screens 5.2.3 UPS Control menu 5.2.4 UPS Status menu 5.2.4 UPS Status menu (continued) 5.2.5 UPS Diagnostics menu 5.2.5 UPS Diagnostics menu (continued) 5.2.6 UPS Setup Page 5.2.6 UPS Setup (continued) 5.2.7 UPS Tests 5.2.8 Password protection 6.0 UPS Monitoring 6.1 Overview 6.2 Interface Kits 6.3 PowerChute Software 6.0 UPS Monitoring 6.4 Computer Interface port 7.0 Difficulty 7.0 Difficult 7.0 Schwierigkeit 7.0 Dificultad Page 7.2 Fault messages 7.2.1 Replace Electronics Unit (EU) 7.2.2 UPS requires service 7.3 Replacing the Electronics Unit 7.4 Replacing or adding Battery Packs 7.5 Obtaining Service 8.0 Storing the UPS 8.1 Storage conditions 8.2 Extended storage 9.0 Specifications 9.1 Input 9.2 Transfer Characteristics 9.3 Output Characteristics 9.4 Noise and surge isolation 9.0 Specifications 9.5 Battery Pack 9.6 Environment 9.7 Physical 9.8 Approvals Page Page Page Page DECLARATION OF CONFORMITY Toll free technical support: Return shipment addresses: