American Power Conversion 3000, 5000

4Battery Pack panel coupler

Additional Battery Packs are connected to this panel coupler. A coupler clamp is

installed over the coupler opening as furnished from the factory. See the Installation

section of this manual for instructions on how to lock mated couplers.

5Battery Pack cables

Each Battery Pack cable is made from welding grade wire to withstand abrasion or

crimping in rough duty applications.

6Replace Battery indicator

The Replace Battery indicator is illuminated when the Battery Pack can no longer

sustain a charge due to wear. See the Difficulty section of this manual if the indicator

is lit.

7In-line Battery Pack coupler

The in-line Battery Pack coupler connects to the UPS or to the panel coupler on

another Battery Pack.

8Battery communications cable

Each Battery Pack is supplied with a battery communications cable.

3.0 Presentation

Contents

Main Important safety instructions! Radio frequency interference Limited Warranty Life Support Policy Table of Contents 1.0 Introduction 1.1 Overview 1.0 Introduction 1.2 Hot swappable modules 1.3 Emergency Power Off (EPO) 1.4 Display 1.5 Remote interfaces 2.0 Safety! CAUTION! 2.0 Scurit! ATTENTION! 2.0 Sicherheit! VORSICHT! 2.0 Seguridad! ATENCION! 3.1 Isolation Unit (IU) Page 3.2 Electronics Unit (EU) Page 3.3 Battery Pack Page 4.1 Receiving inspection 4.2 Protection Strategies 4.3 Moving the UPS Page 4.5 Input voltage requirements 4.5.1 208 Vac operation 4.5.2 220240 Vac operation 4.6 Installation procedures 4.6.1 Required materials 4.6.2 Required tools 4.7 Input hard wiring procedure Page 4.7 Input hard wiring procedure (continued) 4.8 Input voltage tap selection208 Vac, 50/60 Hz use only Input voltage select wire (red) 4.9 Output wiring procedure Jumper cord 4.9 Output wiring procedure (continued) 4.10 Module interconnections 4.0 Installation 4.10 Module interconnections (continued) 4.11 Emergency Power Off (EPO) interface pin 6 offset latch jack pin 1 offset latch plug N UPS Loads 5.1 Modes of operation 5.1.1 Sleep mode 5.1.2 Standby mode 5.1.3 On-line mode 5.1.4 On-battery mode 5.1.5 Bypass mode 5.1.6 Transfer between modes of operation 5.2 Display and controls operation 5.2.1 Default screens 5.2.2 Main menu screens 5.2.3 UPS Control menu 5.2.4 UPS Status menu 5.2.4 UPS Status menu (continued) 5.2.5 UPS Diagnostics menu 5.2.5 UPS Diagnostics menu (continued) 5.2.6 UPS Setup Page 5.2.6 UPS Setup (continued) 5.2.7 UPS Tests 5.2.8 Password protection 6.0 UPS Monitoring 6.1 Overview 6.2 Interface Kits 6.3 PowerChute Software 6.0 UPS Monitoring 6.4 Computer Interface port 7.0 Difficulty 7.0 Difficult 7.0 Schwierigkeit 7.0 Dificultad Page 7.2 Fault messages 7.2.1 Replace Electronics Unit (EU) 7.2.2 UPS requires service 7.3 Replacing the Electronics Unit 7.4 Replacing or adding Battery Packs 7.5 Obtaining Service 8.0 Storing the UPS 8.1 Storage conditions 8.2 Extended storage 9.0 Specifications 9.1 Input 9.2 Transfer Characteristics 9.3 Output Characteristics 9.4 Noise and surge isolation 9.0 Specifications 9.5 Battery Pack 9.6 Environment 9.7 Physical 9.8 Approvals Page Page Page Page DECLARATION OF CONFORMITY Toll free technical support: Return shipment addresses: