American Power Conversion 3000, 5000 4.0 Installation

4.0 Installation

4.10 Module interconnections (continued)

Follow the instructions below to install the battery communications cables.

4.10.5 Mate the battery cable plugs in the fashion illustrated below.

4.10.6 Each cable must connect between a Battery Pack OUTPUT and either the

UPSs BATT COMM input, or another Battery Pack INPUT.

TO: UPS BATT COM, or

TO: Battery Pack INPUT

FROM: Battery Pack OUTPUT

(multiple Battery Pack systems)

Typical installation showing mated battery communications cables.

Contents

Main Important safety instructions! Radio frequency interference Limited Warranty Life Support Policy Table of Contents 1.0 Introduction 1.1 Overview 1.0 Introduction 1.2 Hot swappable modules 1.3 Emergency Power Off (EPO) 1.4 Display 1.5 Remote interfaces 2.0 Safety! CAUTION! 2.0 Scurit! ATTENTION! 2.0 Sicherheit! VORSICHT! 2.0 Seguridad! ATENCION! 3.1 Isolation Unit (IU) Page 3.2 Electronics Unit (EU) Page 3.3 Battery Pack Page 4.1 Receiving inspection 4.2 Protection Strategies 4.3 Moving the UPS Page 4.5 Input voltage requirements 4.5.1 208 Vac operation 4.5.2 220240 Vac operation 4.6 Installation procedures 4.6.1 Required materials 4.6.2 Required tools 4.7 Input hard wiring procedure Page 4.7 Input hard wiring procedure (continued) 4.8 Input voltage tap selection208 Vac, 50/60 Hz use only Input voltage select wire (red) 4.9 Output wiring procedure Jumper cord 4.9 Output wiring procedure (continued) 4.10 Module interconnections 4.0 Installation 4.10 Module interconnections (continued) 4.11 Emergency Power Off (EPO) interface pin 6 offset latch jack pin 1 offset latch plug N UPS Loads 5.1 Modes of operation 5.1.1 Sleep mode 5.1.2 Standby mode 5.1.3 On-line mode 5.1.4 On-battery mode 5.1.5 Bypass mode 5.1.6 Transfer between modes of operation 5.2 Display and controls operation 5.2.1 Default screens 5.2.2 Main menu screens 5.2.3 UPS Control menu 5.2.4 UPS Status menu 5.2.4 UPS Status menu (continued) 5.2.5 UPS Diagnostics menu 5.2.5 UPS Diagnostics menu (continued) 5.2.6 UPS Setup Page 5.2.6 UPS Setup (continued) 5.2.7 UPS Tests 5.2.8 Password protection 6.0 UPS Monitoring 6.1 Overview 6.2 Interface Kits 6.3 PowerChute Software 6.0 UPS Monitoring 6.4 Computer Interface port 7.0 Difficulty 7.0 Difficult 7.0 Schwierigkeit 7.0 Dificultad Page 7.2 Fault messages 7.2.1 Replace Electronics Unit (EU) 7.2.2 UPS requires service 7.3 Replacing the Electronics Unit 7.4 Replacing or adding Battery Packs 7.5 Obtaining Service 8.0 Storing the UPS 8.1 Storage conditions 8.2 Extended storage 9.0 Specifications 9.1 Input 9.2 Transfer Characteristics 9.3 Output Characteristics 9.4 Noise and surge isolation 9.0 Specifications 9.5 Battery Pack 9.6 Environment 9.7 Physical 9.8 Approvals Page Page Page Page DECLARATION OF CONFORMITY Toll free technical support: Return shipment addresses: