American Power Conversion 3000, 5000 3.3 Battery Pack

3.0 Presentation

3.3 Battery Pack

1Battery Pack

The Battery Pack contains four series connected nominal 12 Vdc high capacity sealed

lead-acid batteries. Built-in ultra-low power consumption battery pack voltage and

current monitoring electronics report pack status to the UPS. To conserve battery

capacity, the internal electronics are shut down when the battery communications

cable is not connected to the UPS, or when the UPS is not running.

2INPUT battery communications jack

This input accepts battery status signals from the OUTPUT of another Battery Pack in

the system. No connection is made to this jack in a single Battery Pack system.

3OUTPUT battery communications jack

The Battery Pack sends status signals to the UPS or to the INPUT of another Battery

Pack (in a multiple Battery Pack system) from this jack.

Rear view Front view

4 5

Contents

Main Important safety instructions! Radio frequency interference Limited Warranty Life Support Policy Table of Contents 1.0 Introduction 1.1 Overview 1.0 Introduction 1.2 Hot swappable modules 1.3 Emergency Power Off (EPO) 1.4 Display 1.5 Remote interfaces 2.0 Safety! CAUTION! 2.0 Scurit! ATTENTION! 2.0 Sicherheit! VORSICHT! 2.0 Seguridad! ATENCION! 3.1 Isolation Unit (IU) Page 3.2 Electronics Unit (EU) Page 3.3 Battery Pack Page 4.1 Receiving inspection 4.2 Protection Strategies 4.3 Moving the UPS Page 4.5 Input voltage requirements 4.5.1 208 Vac operation 4.5.2 220240 Vac operation 4.6 Installation procedures 4.6.1 Required materials 4.6.2 Required tools 4.7 Input hard wiring procedure Page 4.7 Input hard wiring procedure (continued) 4.8 Input voltage tap selection208 Vac, 50/60 Hz use only Input voltage select wire (red) 4.9 Output wiring procedure Jumper cord 4.9 Output wiring procedure (continued) 4.10 Module interconnections 4.0 Installation 4.10 Module interconnections (continued) 4.11 Emergency Power Off (EPO) interface pin 6 offset latch jack pin 1 offset latch plug N UPS Loads 5.1 Modes of operation 5.1.1 Sleep mode 5.1.2 Standby mode 5.1.3 On-line mode 5.1.4 On-battery mode 5.1.5 Bypass mode 5.1.6 Transfer between modes of operation 5.2 Display and controls operation 5.2.1 Default screens 5.2.2 Main menu screens 5.2.3 UPS Control menu 5.2.4 UPS Status menu 5.2.4 UPS Status menu (continued) 5.2.5 UPS Diagnostics menu 5.2.5 UPS Diagnostics menu (continued) 5.2.6 UPS Setup Page 5.2.6 UPS Setup (continued) 5.2.7 UPS Tests 5.2.8 Password protection 6.0 UPS Monitoring 6.1 Overview 6.2 Interface Kits 6.3 PowerChute Software 6.0 UPS Monitoring 6.4 Computer Interface port 7.0 Difficulty 7.0 Difficult 7.0 Schwierigkeit 7.0 Dificultad Page 7.2 Fault messages 7.2.1 Replace Electronics Unit (EU) 7.2.2 UPS requires service 7.3 Replacing the Electronics Unit 7.4 Replacing or adding Battery Packs 7.5 Obtaining Service 8.0 Storing the UPS 8.1 Storage conditions 8.2 Extended storage 9.0 Specifications 9.1 Input 9.2 Transfer Characteristics 9.3 Output Characteristics 9.4 Noise and surge isolation 9.0 Specifications 9.5 Battery Pack 9.6 Environment 9.7 Physical 9.8 Approvals Page Page Page Page DECLARATION OF CONFORMITY Toll free technical support: Return shipment addresses: