American Power Conversion BI800F, BI800T user manual Power Inverter Indicators

OVER

25% 50% 75% 100% LOAD

INVERTER LOAD

AWAY

TEST

MUTE HOME

INVERTER		ON	ON
DISABLE	MAINS BATTERY FAULT

Figure 11. Power Inverter Front Panel Controls and Indicators

Table 1. Power Inverter Indicators

	On Mains	On Battery	Fault	INV	25%	50%	75%	100%	Overload
Mode				Disable						Buzzer	Description
	(green)	(yellow)	(red)		(green)	(green)	(green)	(green)	(red)
				(red)
ON LINE	On	Off	Off	Off	Off	Off	Off	Off	Off	Off	The unit is ON-LINE.
ON LINE SELF TEST	Flashing	Off	Off	Off	Off	Off	Off	Off	Off	Off	The unit is in ON-LINE Self-
											Test mode.
ON BATTERY SELF	Flashing	On	Off	Off	On	Off	Off	Off	Off	Off	The unit is in ON-BATTERY
TEST											Self-Test mode, and the load
											is less than 25%.
	Flashing	On	Off	Off	On	On	Off	Off	Off	Off	The unit is in ON-BATTERY
											Self-Test mode, and the load
											is between 25% - 50%.
	Flashing	On	Off	Off	On	On	On	Off	Off	Off	The unit is in ON BATTERY
											Self-Test mode, and the load
											is between 50% - 75%.
	Flashing	On	Off	Off	On	On	On	On	Off	Off	The unit is in ON-BATTERY
											Self-Test mode, and the load
											is more than 75% but less
											than oveload limit.
	Flashing	On	Off	Off	On	On	On	On	On	Continuous beep for	The unit is in ON-BATTERY
										first 30 seconds for a	Self-Test mode, and is in an
										fresh overload.	overload condition.
ON BATTERY	Off	On	Off	Off	On	Off	Off	Off	Off	4 beeps every 22	The unit is in ON-BATTERY
										minutes	mode, and the load is less
											than 25%.
	Off	On	Off	Off	On	On	Off	Off	Off	4 beeps every 22	The unit is in ON-BATTERY
										minutes	mde, and the load is between
											25% and 50%.
	Off	On	Off	Off	On	On	On	Off	Off	4 beeps every 22	The unit is in ON-BATTERY
										minutes	mode, and the load is
											between 50% and 75%.
	Off	On	Off	Off	On	On	On	On	Off	4 beeps every 22	The unit is in ON BATTERY
										minutes	mode; the load is between
											75% and the overload limit.
	Off	On	Off	Off	On	On	On	On	On	Continuous beep for	The unit is in ON-BATTERY
										first 30 seconds of a	mode, and is in overload
										new overload.	condition (see NOTE below).
STANDBY ENABLE	Off	Off	Off	Off	Off	Off	Off	Off	Off	Short beep every 5	The unit is shut down due to a
										seconds	LOW BATTERY.
STANDBY	Off	Off	Off	Off	Off	Off	Off	Off	Off	Off	The unit is in STANDBY
											mode, and is not powering
											the load.
FAULT -	Off	Off	Off	Off	On	On	On	On	On	Off	Iverter load capacity has
											been exceeded (see NOTE
											below).
FAULT-	Flashing	Flashing	Flashing	Off	Off	Off	Off	Off	Off	Off	The unit is in FAULT mode,
											contact APC Technical
											Support.
FAULT-	Off	Off	On	Off	Off	Off	Off	Off	Off	Continuously On	The unit is in FAULT mode,
											contact APC Technical
											Support.

Page 10