Manuals / Antec / Computer Equipment / Computer Accessories

Antec DF-30 user manual INTERNAL 3.5” DEVICE INSTALLATION, Open the Fleet-ReleaseTM access door

Models: DF-30

1 30

Download 30 pages 57.34 Kb

Page 16

Image 16

2.5

INTERNAL 3.5” DEVICE INSTALLATION

The DF-30 includes two Fleet-Release™access doors. With the front bezel facing you, they are located by default on the bottom nine drive bay slots (each door covers three drive bays).

1.Open the Fleet-ReleaseTMaccess door.

Opening the Fleet-Release™ access door by gently

pressing the left side to release it, and then swing it open.

2.Insert your 3.5” device into the 3.5” drive cage from the front of the case. You will feel resistance from presstabs on either side of the drive cage which will create friction against the drive. Push gently until the drive’s mounting holes align with the screw holes in the cage.

Page 16

Image 16

Antec DF-30 user manual INTERNAL 3.5” DEVICE INSTALLATION, Open the Fleet-ReleaseTM access door

Contents

D F - 3 THE ADVANCED GAMING FORCEDARKFLEET U S E R M A N U A LDF-30 USER’S MANUAL DisclaimerTABLE OF CONTENTS SECTION 1 INTRODUCTION Drive bays CASE SPECIFICATIONS BEFORE YOU BEGIN LOCATING AND POSITIONING YOUR COMPUTER INSTALLATION SECTION 2 HARDWARESETTING UP C - 3.5” drive bay area D - Front panel wiring E - I/O panel A - Power supply mounts B - 5.25” drive bay areaE D B C A MOTHERBOARD INSTALLATION Before proceedingMake sure you have the correct I/O panel. This mismatched I/O panel can cause difficulties down the roadLift your motherboard out to install the standoffs 4. Install standoffs as needed and put the motherboard back inStep 5 Screwing in the motherboard after standoffs are installed 3. Now remove your motherboard by lifting it upSTANDARD ATX POWER SUPPLY INSTALLATION The DF-30 can accommodate a standard-size ATX power supplyNote The DF-30 comes with a CPU cutout on the motherboard tray, which PSU resting on the standard PSU mountCABLE MANAGEMENT Use these screws to secure your power supply to the case3. Use the cable ties provided to hold them in place INTERNAL 3.5” DEVICE INSTALLATION 1. Open the Fleet-ReleaseTM access doorOpening the Fleet-Release access door by gently pressing the left side to release it, and then swing it openInstalling a 3.5” internal device Make sure to install screws on the left side…6. Close the Fleet-Release access door 4. Mount any other 3.5” HDD devices accordinglyEXTERNAL 3.5” DEVICE INSTALLATION There is one external 3.5” drive bay under the 5.25” drive baysRemove this drive bay cover Insert your drive as shownUsing the top 2.5” hot-swap drive bay USING THE TOP 2.5” HOT-SWAP BAY2. Push the HDD all the way into the bay until it locks into position EXTERNAL 5.25” DEVICE INSTALLATION 5.25” device installationThe plastic drive bay faceplate should pop free A screwdriver may be needed to remove the metal cover plateINTERNAL 2. 5” DEVICE INSTALLATION 2. Using the screws provided, secure your 2.5” device1. Locate the bay at the bottom of the case The 2.5” mounting locationFRONT I/O PORTSSECTION AC’97 / HD AUDIO PORTS Key No ConnectionNote Polarity positive and negative does not matter for switches POWER SWITCH / RESET SWITCH / HARD DISK DRIVE LED CONNECTORSFront Panel switch leads REWIRING MOTHERBOARD HEADER CONNECTIONSSYSTEM SECTION 4 COOLINGINCLUDED FANS Standard fans on the DF-30 A - 1 x 120 mm rear TwoCool LED fanB - 1 x 140 mm top TwoCool fan Rear fan control panelTOP 140 MM TWOCOOL FAN Turn this knob to adjust the fanFRONT 120 MM BLUE LED FANS REAR EXHAUST 120 MM TWOCOOL FANS OPTIONAL FANSTo clean the filter All trademarks are the property of their respective owners Copyright 2010 Antec, Inc. All rights reservedPrinted in China