Manuals
/
Antec
/
Computer Equipment
/
Computer Accessories
Antec
DF-30 user manual Ports, Front I/O, Section
Models:
DF-30
1
22
30
30
Download
30 pages
57.34 Kb
19
20
21
22
23
24
25
26
<
>
Specs
Install
C - 3.5” drive bay area D - Front panel wiring E - I/O panel
Power Switch / Reset Switch / Hard Disk Drive Led Connectors
Setting Up
Turn this knob to adjust the fan
To clean the filter
The DF-30 can accommodate a standard-size ATX power supply
Open the Fleet-ReleaseTM access door
USING THE TOP 2.5” HOT-SWAP BAY
Page 22
Image 22
3.
S
ECTION
3
F
RONT
I/O
P
ORTS
22
Page 21
Page 23
Page 22
Image 22
Page 21
Page 23
Contents
DARKFLEET
D F - 3
THE ADVANCED GAMING FORCE
U S E R M A N U A L
DF-30 USER’S MANUAL
Disclaimer
TABLE OF CONTENTS
SECTION 1 INTRODUCTION
Drive bays
CASE SPECIFICATIONS
BEFORE YOU BEGIN
LOCATING AND POSITIONING YOUR COMPUTER
INSTALLATION
SECTION 2 HARDWARE
SETTING UP
C - 3.5” drive bay area D - Front panel wiring E - I/O panel
A - Power supply mounts B - 5.25” drive bay area
E D B C A
Make sure you have the correct I/O panel. This mismatched I/O panel
MOTHERBOARD INSTALLATION
Before proceeding
can cause difficulties down the road
Step 5 Screwing in the motherboard after standoffs are installed
Lift your motherboard out to install the standoffs
4. Install standoffs as needed and put the motherboard back in
3. Now remove your motherboard by lifting it up
Note The DF-30 comes with a CPU cutout on the motherboard tray, which
STANDARD ATX POWER SUPPLY INSTALLATION
The DF-30 can accommodate a standard-size ATX power supply
PSU resting on the standard PSU mount
CABLE MANAGEMENT
Use these screws to secure your power supply to the case
3. Use the cable ties provided to hold them in place
Opening the Fleet-Release access door by gently
INTERNAL 3.5” DEVICE INSTALLATION
1. Open the Fleet-ReleaseTM access door
pressing the left side to release it, and then swing it open
6. Close the Fleet-Release access door
Installing a 3.5” internal device
Make sure to install screws on the left side…
4. Mount any other 3.5” HDD devices accordingly
Remove this drive bay cover
EXTERNAL 3.5” DEVICE INSTALLATION
There is one external 3.5” drive bay under the 5.25” drive bays
Insert your drive as shown
Using the top 2.5” hot-swap drive bay
USING THE TOP 2.5” HOT-SWAP BAY
2. Push the HDD all the way into the bay until it locks into position
The plastic drive bay faceplate should pop free
EXTERNAL 5.25” DEVICE INSTALLATION
5.25” device installation
A screwdriver may be needed to remove the metal cover plate
1. Locate the bay at the bottom of the case
INTERNAL 2. 5” DEVICE INSTALLATION
2. Using the screws provided, secure your 2.5” device
The 2.5” mounting location
FRONT I/O
PORTS
SECTION
AC’97 / HD AUDIO PORTS
Key No Connection
Front Panel switch leads
Note Polarity positive and negative does not matter for switches
POWER SWITCH / RESET SWITCH / HARD DISK DRIVE LED CONNECTORS
REWIRING MOTHERBOARD HEADER CONNECTIONS
SYSTEM
SECTION 4 COOLING
B - 1 x 140 mm top TwoCool fan
INCLUDED FANS
Standard fans on the DF-30 A - 1 x 120 mm rear TwoCool LED fan
Rear fan control panel
TOP 140 MM TWOCOOL FAN
Turn this knob to adjust the fan
FRONT 120 MM BLUE LED FANS
REAR EXHAUST 120 MM TWOCOOL FANS
OPTIONAL FANS
To clean the filter
All trademarks are the property of their respective owners
Copyright 2010 Antec, Inc. All rights reserved
Printed in China