Manuals / Antec / Computer Equipment / Computer Accessories

Antec Included Fans, Standard fans on the DF-30 A - 1 x 120 mm rear TwoCool LED fan, A B C

Models: DF-30

1 30

Download 30 pages 57.34 Kb

Page 26

Image 26

4.1

INCLUDED FANS

A

Standard fans on the DF-30:

A – 1 x 120 mm rear TwoCool™ LED fan

B – 1 x 140 mm top TwoCool™ fan

C – 2 x Fleet-Release access door modules w/front variable-speed 120 mm blue LED fans

Rear fan control panel

Page 26

Image 26

Antec Included Fans, Standard fans on the DF-30 A - 1 x 120 mm rear TwoCool LED fan, B - 1 x 140 mm top TwoCool fan

Contents

DARKFLEET D F - 3THE ADVANCED GAMING FORCE U S E R M A N U A LDF-30 USER’S MANUAL DisclaimerTABLE OF CONTENTS SECTION 1 INTRODUCTION Drive bays CASE SPECIFICATIONS BEFORE YOU BEGIN LOCATING AND POSITIONING YOUR COMPUTER INSTALLATION SECTION 2 HARDWARESETTING UP E D B C A A - Power supply mounts B - 5.25” drive bay areaC - 3.5” drive bay area D - Front panel wiring E - I/O panel Make sure you have the correct I/O panel. This mismatched I/O panel MOTHERBOARD INSTALLATIONBefore proceeding can cause difficulties down the roadStep 5 Screwing in the motherboard after standoffs are installed Lift your motherboard out to install the standoffs4. Install standoffs as needed and put the motherboard back in 3. Now remove your motherboard by lifting it upNote The DF-30 comes with a CPU cutout on the motherboard tray, which STANDARD ATX POWER SUPPLY INSTALLATIONThe DF-30 can accommodate a standard-size ATX power supply PSU resting on the standard PSU mount3. Use the cable ties provided to hold them in place Use these screws to secure your power supply to the caseCABLE MANAGEMENT Opening the Fleet-Release access door by gently INTERNAL 3.5” DEVICE INSTALLATION1. Open the Fleet-ReleaseTM access door pressing the left side to release it, and then swing it open6. Close the Fleet-Release access door Installing a 3.5” internal deviceMake sure to install screws on the left side… 4. Mount any other 3.5” HDD devices accordinglyRemove this drive bay cover EXTERNAL 3.5” DEVICE INSTALLATIONThere is one external 3.5” drive bay under the 5.25” drive bays Insert your drive as shown2. Push the HDD all the way into the bay until it locks into position USING THE TOP 2.5” HOT-SWAP BAYUsing the top 2.5” hot-swap drive bay The plastic drive bay faceplate should pop free EXTERNAL 5.25” DEVICE INSTALLATION5.25” device installation A screwdriver may be needed to remove the metal cover plate1. Locate the bay at the bottom of the case INTERNAL 2. 5” DEVICE INSTALLATION2. Using the screws provided, secure your 2.5” device The 2.5” mounting locationSECTION PORTSFRONT I/O AC’97 / HD AUDIO PORTS Key No ConnectionFront Panel switch leads Note Polarity positive and negative does not matter for switchesPOWER SWITCH / RESET SWITCH / HARD DISK DRIVE LED CONNECTORS REWIRING MOTHERBOARD HEADER CONNECTIONSSYSTEM SECTION 4 COOLINGB - 1 x 140 mm top TwoCool fan INCLUDED FANSStandard fans on the DF-30 A - 1 x 120 mm rear TwoCool LED fan Rear fan control panelFRONT 120 MM BLUE LED FANS Turn this knob to adjust the fanTOP 140 MM TWOCOOL FAN REAR EXHAUST 120 MM TWOCOOL FANS OPTIONAL FANSTo clean the filter Printed in China Copyright 2010 Antec, Inc. All rights reservedAll trademarks are the property of their respective owners