Manuals
/
Antec
/
Computer Equipment
/
Computer Accessories
Antec
DF-30 user manual Installation, Hardware
Models:
DF-30
1
9
30
30
Download
30 pages
57.34 Kb
6
7
8
9
10
11
12
13
<
>
Specification
Install
C - 3.5” drive bay area D - Front panel wiring E - I/O panel
Power Switch / Reset Switch / Hard Disk Drive Led Connectors
Setting Up
Turn this knob to adjust the fan
To clean the filter
The DF-30 can accommodate a standard-size ATX power supply
Open the Fleet-ReleaseTM access door
USING THE TOP 2.5” HOT-SWAP BAY
Page 9
Image 9
S
ECTION
2
H
ARDWARE
I
NSTALLATION
9
Page 8
Page 10
Page 9
Image 9
Page 8
Page 10
Contents
THE ADVANCED GAMING FORCE
D F - 3
DARKFLEET
U S E R M A N U A L
Disclaimer
DF-30 USER’S MANUAL
TABLE OF CONTENTS
SECTION 1 INTRODUCTION
Drive bays
CASE SPECIFICATIONS
BEFORE YOU BEGIN
LOCATING AND POSITIONING YOUR COMPUTER
SECTION 2 HARDWARE
INSTALLATION
SETTING UP
A - Power supply mounts B - 5.25” drive bay area
C - 3.5” drive bay area D - Front panel wiring E - I/O panel
E D B C A
Before proceeding
MOTHERBOARD INSTALLATION
Make sure you have the correct I/O panel. This mismatched I/O panel
can cause difficulties down the road
4. Install standoffs as needed and put the motherboard back in
Lift your motherboard out to install the standoffs
Step 5 Screwing in the motherboard after standoffs are installed
3. Now remove your motherboard by lifting it up
The DF-30 can accommodate a standard-size ATX power supply
STANDARD ATX POWER SUPPLY INSTALLATION
Note The DF-30 comes with a CPU cutout on the motherboard tray, which
PSU resting on the standard PSU mount
Use these screws to secure your power supply to the case
CABLE MANAGEMENT
3. Use the cable ties provided to hold them in place
1. Open the Fleet-ReleaseTM access door
INTERNAL 3.5” DEVICE INSTALLATION
Opening the Fleet-Release access door by gently
pressing the left side to release it, and then swing it open
Make sure to install screws on the left side…
Installing a 3.5” internal device
6. Close the Fleet-Release access door
4. Mount any other 3.5” HDD devices accordingly
There is one external 3.5” drive bay under the 5.25” drive bays
EXTERNAL 3.5” DEVICE INSTALLATION
Remove this drive bay cover
Insert your drive as shown
USING THE TOP 2.5” HOT-SWAP BAY
Using the top 2.5” hot-swap drive bay
2. Push the HDD all the way into the bay until it locks into position
5.25” device installation
EXTERNAL 5.25” DEVICE INSTALLATION
The plastic drive bay faceplate should pop free
A screwdriver may be needed to remove the metal cover plate
2. Using the screws provided, secure your 2.5” device
INTERNAL 2. 5” DEVICE INSTALLATION
1. Locate the bay at the bottom of the case
The 2.5” mounting location
PORTS
FRONT I/O
SECTION
Key No Connection
AC’97 / HD AUDIO PORTS
POWER SWITCH / RESET SWITCH / HARD DISK DRIVE LED CONNECTORS
Note Polarity positive and negative does not matter for switches
Front Panel switch leads
REWIRING MOTHERBOARD HEADER CONNECTIONS
SECTION 4 COOLING
SYSTEM
Standard fans on the DF-30 A - 1 x 120 mm rear TwoCool LED fan
INCLUDED FANS
B - 1 x 140 mm top TwoCool fan
Rear fan control panel
Turn this knob to adjust the fan
TOP 140 MM TWOCOOL FAN
FRONT 120 MM BLUE LED FANS
OPTIONAL FANS
REAR EXHAUST 120 MM TWOCOOL FANS
To clean the filter
Copyright 2010 Antec, Inc. All rights reserved
All trademarks are the property of their respective owners
Printed in China
HARDWARE HARDWARE