Manuals / Antec / Computer Equipment / Computer Accessories

Antec DF-30 user manual EXTERNAL 3.5” DEVICE INSTALLATION, Remove this drive bay cover

Models: DF-30

1 30

Download 30 pages 57.34 Kb

Page 18

Image 18

2.6

EXTERNAL 3.5” DEVICE INSTALLATION

There is one external 3.5” drive bay under the 5.25” drive bays.

Remove this drive bay cover.

1.Carefully remove the 3.5” drive bay cover from the bezel. Load the drives from the front, lining them up to the front of the drive cage.

Insert your drive as shown.

2.With one hand supporting the drive, fasten the drive with the screws provided.

3.Find a small 4-pin white connector on the power supply and connect it to the male 4-pin connector on the floppy drive.

Page 18

Image 18

Antec DF-30 user manual EXTERNAL 3.5” DEVICE INSTALLATION, There is one external 3.5” drive bay under the 5.25” drive bays

Contents

DARKFLEET D F - 3THE ADVANCED GAMING FORCE U S E R M A N U A LDF-30 USER’S MANUAL DisclaimerTABLE OF CONTENTS SECTION 1 INTRODUCTION Drive bays CASE SPECIFICATIONS BEFORE YOU BEGIN LOCATING AND POSITIONING YOUR COMPUTER INSTALLATION SECTION 2 HARDWARESETTING UP A - Power supply mounts B - 5.25” drive bay area C - 3.5” drive bay area D - Front panel wiring E - I/O panelE D B C A Make sure you have the correct I/O panel. This mismatched I/O panel MOTHERBOARD INSTALLATIONBefore proceeding can cause difficulties down the roadStep 5 Screwing in the motherboard after standoffs are installed Lift your motherboard out to install the standoffs4. Install standoffs as needed and put the motherboard back in 3. Now remove your motherboard by lifting it upNote The DF-30 comes with a CPU cutout on the motherboard tray, which STANDARD ATX POWER SUPPLY INSTALLATIONThe DF-30 can accommodate a standard-size ATX power supply PSU resting on the standard PSU mountUse these screws to secure your power supply to the case CABLE MANAGEMENT3. Use the cable ties provided to hold them in place Opening the Fleet-Release access door by gently INTERNAL 3.5” DEVICE INSTALLATION1. Open the Fleet-ReleaseTM access door pressing the left side to release it, and then swing it open6. Close the Fleet-Release access door Installing a 3.5” internal deviceMake sure to install screws on the left side… 4. Mount any other 3.5” HDD devices accordinglyRemove this drive bay cover EXTERNAL 3.5” DEVICE INSTALLATIONThere is one external 3.5” drive bay under the 5.25” drive bays Insert your drive as shownUSING THE TOP 2.5” HOT-SWAP BAY Using the top 2.5” hot-swap drive bay2. Push the HDD all the way into the bay until it locks into position The plastic drive bay faceplate should pop free EXTERNAL 5.25” DEVICE INSTALLATION5.25” device installation A screwdriver may be needed to remove the metal cover plate1. Locate the bay at the bottom of the case INTERNAL 2. 5” DEVICE INSTALLATION2. Using the screws provided, secure your 2.5” device The 2.5” mounting locationPORTS FRONT I/OSECTION AC’97 / HD AUDIO PORTS Key No ConnectionFront Panel switch leads Note Polarity positive and negative does not matter for switchesPOWER SWITCH / RESET SWITCH / HARD DISK DRIVE LED CONNECTORS REWIRING MOTHERBOARD HEADER CONNECTIONSSYSTEM SECTION 4 COOLINGB - 1 x 140 mm top TwoCool fan INCLUDED FANSStandard fans on the DF-30 A - 1 x 120 mm rear TwoCool LED fan Rear fan control panelTurn this knob to adjust the fan TOP 140 MM TWOCOOL FANFRONT 120 MM BLUE LED FANS REAR EXHAUST 120 MM TWOCOOL FANS OPTIONAL FANSTo clean the filter Copyright 2010 Antec, Inc. All rights reserved All trademarks are the property of their respective ownersPrinted in China