Manuals / Antec / Computer Equipment / Computer Accessories

Antec DF-30 INTERNAL 2. 5” DEVICE INSTALLATION, Locate the bay at the bottom of the case

Models: DF-30

1 30

Download 30 pages 57.34 Kb

Page 21

Image 21

2.9

INTERNAL 2. 5” DEVICE INSTALLATION

There is a 2.5” device mounting location located at the bottom of the case. To use this mounting location:

1.Locate the bay at the bottom of the case.

The 2.5” mounting location

2.Using the screws provided, secure your 2.5” device.

Secure your 2.5” device from the bottom.

Page 21

Image 21

Antec DF-30 INTERNAL 2. 5” DEVICE INSTALLATION, Locate the bay at the bottom of the case, The 2.5” mounting location

Contents

THE ADVANCED GAMING FORCE D F - 3DARKFLEET U S E R M A N U A LDisclaimer DF-30 USER’S MANUALTABLE OF CONTENTS SECTION 1 INTRODUCTION Drive bays CASE SPECIFICATIONS BEFORE YOU BEGIN LOCATING AND POSITIONING YOUR COMPUTER SECTION 2 HARDWARE INSTALLATIONSETTING UP A - Power supply mounts B - 5.25” drive bay area C - 3.5” drive bay area D - Front panel wiring E - I/O panelE D B C A Before proceeding MOTHERBOARD INSTALLATIONMake sure you have the correct I/O panel. This mismatched I/O panel can cause difficulties down the road4. Install standoffs as needed and put the motherboard back in Lift your motherboard out to install the standoffsStep 5 Screwing in the motherboard after standoffs are installed 3. Now remove your motherboard by lifting it upThe DF-30 can accommodate a standard-size ATX power supply STANDARD ATX POWER SUPPLY INSTALLATIONNote The DF-30 comes with a CPU cutout on the motherboard tray, which PSU resting on the standard PSU mountUse these screws to secure your power supply to the case CABLE MANAGEMENT3. Use the cable ties provided to hold them in place 1. Open the Fleet-ReleaseTM access door INTERNAL 3.5” DEVICE INSTALLATIONOpening the Fleet-Release access door by gently pressing the left side to release it, and then swing it openMake sure to install screws on the left side… Installing a 3.5” internal device6. Close the Fleet-Release access door 4. Mount any other 3.5” HDD devices accordinglyThere is one external 3.5” drive bay under the 5.25” drive bays EXTERNAL 3.5” DEVICE INSTALLATIONRemove this drive bay cover Insert your drive as shownUSING THE TOP 2.5” HOT-SWAP BAY Using the top 2.5” hot-swap drive bay2. Push the HDD all the way into the bay until it locks into position 5.25” device installation EXTERNAL 5.25” DEVICE INSTALLATIONThe plastic drive bay faceplate should pop free A screwdriver may be needed to remove the metal cover plate2. Using the screws provided, secure your 2.5” device INTERNAL 2. 5” DEVICE INSTALLATION1. Locate the bay at the bottom of the case The 2.5” mounting locationPORTS FRONT I/OSECTION Key No Connection AC’97 / HD AUDIO PORTSPOWER SWITCH / RESET SWITCH / HARD DISK DRIVE LED CONNECTORS Note Polarity positive and negative does not matter for switchesFront Panel switch leads REWIRING MOTHERBOARD HEADER CONNECTIONSSECTION 4 COOLING SYSTEMStandard fans on the DF-30 A - 1 x 120 mm rear TwoCool LED fan INCLUDED FANSB - 1 x 140 mm top TwoCool fan Rear fan control panelTurn this knob to adjust the fan TOP 140 MM TWOCOOL FANFRONT 120 MM BLUE LED FANS OPTIONAL FANS REAR EXHAUST 120 MM TWOCOOL FANSTo clean the filter Copyright 2010 Antec, Inc. All rights reserved All trademarks are the property of their respective ownersPrinted in China