Manuals / Antec / Computer Equipment / Computer Accessories

Antec DF-30 user manual Drive bays

Models: DF-30

1 30

Download 30 pages 57.34 Kb

Page 5

Image 5

1.1

GETTING TO KNOW YOUR CASE

Drive bays		Hardware mounts
1	5.25” drive bays	8	Motherboard standoffs (pre-
2	3.5” drive bays		installed)
3	2.5” internal SSD bay	9	Power supply mounts
4	2.5” external hot-swap	10	Front I/O ports

Cooling

5140 mm top TwoCool™ fan

6 120 mm rear TwoCool™ fan

7 Fleet-Release access door modules w/front variable- speed 120 mm blue LED fans

Page 5

Image 5

Contents

THE ADVANCED GAMING FORCE D F - 3DARKFLEET U S E R M A N U A LDisclaimer DF-30 USER’S MANUALTABLE OF CONTENTS SECTION 1 INTRODUCTION Drive bays CASE SPECIFICATIONS BEFORE YOU BEGIN LOCATING AND POSITIONING YOUR COMPUTER SECTION 2 HARDWARE INSTALLATIONSETTING UP E D B C A A - Power supply mounts B - 5.25” drive bay areaC - 3.5” drive bay area D - Front panel wiring E - I/O panel Before proceeding MOTHERBOARD INSTALLATIONMake sure you have the correct I/O panel. This mismatched I/O panel can cause difficulties down the road4. Install standoffs as needed and put the motherboard back in Lift your motherboard out to install the standoffsStep 5 Screwing in the motherboard after standoffs are installed 3. Now remove your motherboard by lifting it upThe DF-30 can accommodate a standard-size ATX power supply STANDARD ATX POWER SUPPLY INSTALLATIONNote The DF-30 comes with a CPU cutout on the motherboard tray, which PSU resting on the standard PSU mount3. Use the cable ties provided to hold them in place Use these screws to secure your power supply to the caseCABLE MANAGEMENT 1. Open the Fleet-ReleaseTM access door INTERNAL 3.5” DEVICE INSTALLATIONOpening the Fleet-Release access door by gently pressing the left side to release it, and then swing it openMake sure to install screws on the left side… Installing a 3.5” internal device6. Close the Fleet-Release access door 4. Mount any other 3.5” HDD devices accordinglyThere is one external 3.5” drive bay under the 5.25” drive bays EXTERNAL 3.5” DEVICE INSTALLATIONRemove this drive bay cover Insert your drive as shown2. Push the HDD all the way into the bay until it locks into position USING THE TOP 2.5” HOT-SWAP BAYUsing the top 2.5” hot-swap drive bay 5.25” device installation EXTERNAL 5.25” DEVICE INSTALLATIONThe plastic drive bay faceplate should pop free A screwdriver may be needed to remove the metal cover plate2. Using the screws provided, secure your 2.5” device INTERNAL 2. 5” DEVICE INSTALLATION1. Locate the bay at the bottom of the case The 2.5” mounting locationSECTION PORTSFRONT I/O Key No Connection AC’97 / HD AUDIO PORTSPOWER SWITCH / RESET SWITCH / HARD DISK DRIVE LED CONNECTORS Note Polarity positive and negative does not matter for switchesFront Panel switch leads REWIRING MOTHERBOARD HEADER CONNECTIONSSECTION 4 COOLING SYSTEMStandard fans on the DF-30 A - 1 x 120 mm rear TwoCool LED fan INCLUDED FANSB - 1 x 140 mm top TwoCool fan Rear fan control panelFRONT 120 MM BLUE LED FANS Turn this knob to adjust the fanTOP 140 MM TWOCOOL FAN OPTIONAL FANS REAR EXHAUST 120 MM TWOCOOL FANSTo clean the filter Printed in China Copyright 2010 Antec, Inc. All rights reservedAll trademarks are the property of their respective owners