Certifications and Compliances Safety | Apollo IMY specification

20. CERTIFICATIONS AND COMPLIANCES:

SAFETY

IEC 1010-1, EN 61010-1: Safety requirements for electrical equipment for measurement, control and laboratory use, Part 1.

IP65 Enclosure rating (Face only), IEC 529 Type 4 Enclosure rating (Face only), UL50

ELECTROMAGNETIC COMPATIBILITY

Immunity to EN 50082-2	EN 61000-4-2 Level 2; 4		Kv contact 1
Electrostatic discharge
Electromagnetic RF fields	EN 61000-4-3	Level 3; 8	Kv air
		Level 3; 10 V/m 2
Fast transients (burst)	EN 61000-4-4	80 MHz - 1 GHz
		Level 4; 2	Kv I/O
RF conducted interference	EN 61000-4-6	Level 3; 2	Kv power
		Level 3; 10 V/rms
		150 KHz - 80 MHz
Emissions to EN 50081-2	EN 55011	Enclosure class A
RF interference
Notes:		Power mains class A

1. Metal bezel of unit connected with ground lead from rear bezel screw to metal mounting panel.

2. Self-recoverable loss of performance during EMI disturbance at 10 V/m: Process input and/or analog output signal may vary during EMI disturbance. For operation without loss of performance:

Unit is mounted in a metal enclosure (Buckeye SM7013-0 or equivalent) I/O and power cables are routed in metal conduit connected to earth ground.

Refer to the EMC Installation Guidelines for additional information.

21. CONSTRUCTION: Die-cast metal front bezel that meets NEMA 4/IP65 requirements for wash-down and/or dusty environments when properly installed. Pollution Degree 2. Case body is black, high impact plastic (panel gasket and mounting clips included).

22. CONNECTION: Removable terminal blocks

23. WEIGHT: 1.2 lbs. (0.54 kg)

-40-

Image 42

Apollo IMY instruction manual Certifications and Compliances Safety

Contents

Apollo Intelligent Meter Series Introduction Table of Contents Page Safety Information Safety SummaryDefinition of Terms General Description Theory of Operation Block Diagram Programming and Operating the IMY Programming the IMY Display Module #2 Program Temperature Display Offset and Slope Reset Latched Alarms Display Alarm ValuesEnter Alarm Values Reset PEAK/VALLEY Memory Buffer Temperature Offset Value Enter Offset Value Module #4 Program Digital Filter and Remote Input Program Digital Filtering Program Function of E1-CON and Optional E2-CON Cont’d Module #5 Program INTEGRATOR/TOTALIZER Program Decimal Point Position for the INTEGRATOR/TOTALIZERProgram INTEGRATOR/TOTALIZER Time Base Module #6 Program ALARM/SETPOINT Alarm #2 Assignment to Input or INTEGRATOR/ Totalizer Program Value for Alarm #2Alarm #2 High or LOW Acting Print Request Function Baud RateUnit Address Number Full or Abbreviated Transmission Analog Output LO Display Value Module #8 Program RE-TRANSMITTED Analog OutputAnalog Output Source Analog Output HI Display Value Enter Zero Reference Module #9 Service OperationsEnter Access Code Apply Precision Resistance Operating the IMY Quick Programming Factory Configuration Slope Programming Example Temperature Monitoring Example Offset and Slope Display Temperature INTEGRATOR/TOTALIZERPEAK/VALLEY INTEGRATOR/TOTALIZER Example Basic SET-UPINTEGRATOR/TOTALIZER SET-UP 125 x 827 Alarms Optional Alarm Timing Diagrams General Description Communication Format Sending Commands to the IMY Command String Examples Timing Diagrams Receiving Data from the IMY Current Loop InstallationWiring Connections Serial Terminal Descriptions Connecting to AN RLC Printer Serial Communications Examples Process Controlling System RE-TRANSMITTED Analog Output Optional Analog Output Calibration To 20 mA Calibration Appendix a Installation & Connections Installation EnvironmentSelect AC Power 115/230 VAC EMC Installation Guidelines Wiring Connections Power Wiring Appendix B Specifications and Dimensions Open Thermistor Detection Display Ululul To 20 mA Certifications and Compliances Safety Appendix C Troubleshooting Guide Problem Possible Cause Remedies Appendix D Programmable Functions Decimal Point Positon Appendix D Programmable Functions Cont’d Appendix E Ordering Information E2-CON Limited Warranty IMY/IM-A 3/02 Drawing NO. LP0311