Manuals / Brands / Computer Equipment / Computer Hardware / Apple / Computer Equipment / Computer Hardware

Apple IIGS 1 0 ) ReInstall Any Cards Removed, 1 1 ) Close Computer, 1 2 ) Plug In External Power Cord, 1 3 ) Boot Computer and Set Slots

1 62

Download 62 pages, 306.49 Kb

1 0 ) ReInstall Any Cards Removed

Replace any cards you have removed for the installation following those cards’ installation instructions.

• WARNING! IF YOU HAVE A CARD IN SLOT 1, use

the insulator card (2” x 6”) included with the Vulcan package. Applied Engineering will not be responsible for damage to any other products so be careful when reinstalling your cards.

1 1 ) Close Computer

Replace the lid by sliding the front of the lid in first, lowering the back edge into place and then pushing gently and firmly on the back corners of the lid until it pops into place.

1 2 ) Plug In External Power Cord

This is the same cord as your original power supply used. Connect it to the back of the Vulcan and then plug it into the wall socket.

1 3 ) Boot Computer and Set Slots

You must set the slot containing the controller card to “Your Card” under Slots option of the Control Panel. Refer to your IIGS owner’s manual for more information on setting the slot.

Slot 7 Exception (Pseudo-Slotting)

If you want the card to appear to be in slot 7 even though it’s installed into another slot (as mentioned earlier) you’ll need to set your slots as follows:

1)Leave the slot in which the controller card is installed set to that slot’s function (i.e. not “Your Card”)

2)Set slot 7 to “Your Card.”

• Note: Make sure that you’ve set the switches on the card to the proper position.

1 4 ) Set to Boot from the Vulcan

The Vulcan is preformatted and ready to boot into GS/OS. If you want to boot from the Vulcan, set the Startup Slot under the Slots option to the slot that your Vulcan is in. (If you’re pseudo- slotting, set Startup Slot to 7.)

Hardware installation is complete. Congratulations!

6 Vulcan

Contents

Page Table Of Contents Formatting Print Quit Final Check CHAPTER FIVE - BACKING UP THE VULCAN Introduction Backup II for ProDOS Number of Disks Required Suggested Backup Schedule Page Page INTRODUCTION Getting Started What's Included with the Vulcan The Vulcan's Fan The Power Supply CHAPTER ONE 1 ) Open Computer Remove the IIGS cover 2)Remove Power Supply Unplug Internal Cord Pull Back Tab 3)Remove Vulcan from Packing 4)Check Voltage Setting 5 ) Insert Vulcan 7 ) Set Switches According to Slot Default Switch Setting Insert Controller Card into Slot 1 0 ) ReInstall Any Cards Removed 1 1 ) Close Computer 1 2 ) Plug In External Power Cord 1 3 ) Boot Computer and Set Slots 1 4 ) Set to Boot from the Vulcan Using G S / O S Dividing the Partitions Loading Different Opewting Systems Vulcan CHAPTER Two Remove the //e or ][ Plus cover 2)Remove Cards 3)Remove Power Supply iii)Remove screws 4)Remove Vulcan from Packing 5)Check Voltage Setting 6)][ Plus Users Only --Attach Riser Plates Attach Riser Plates (][ Plus Only) 7)Insert Vulcan 8)Use four screws providedto secure Vulcan 9 ) Plug Internal Power Cord Into Motherboard Plug Internal Cord Into Motherboard 10)Set Switches According to Slot Switch 3, ][+ Boot Enable Switch 3 Set to Boot Enable for ][ Plus and Unenhanced lie Switch 3 Setting for //e Retrofit and Enhanced //e 11)Insert Card Into Slot 12)Connect Cable from Vulcan to Controller Card 13)ReInstall Any Cards Removed 14) Close Computer 15) Plug In External Power Cord Hardware installation is complete. Congratulations’ lIe //e and ][ Plus Users Vulcan CHAPTER THREE The Partition Manager From Disk From Basic From the Finder (GS and lIe retrofit Only) Other Launchers The PM Menu Entering MODIFY Mode LockIng/Unlocking Partitions Partition Names Setting the Partition Size BACK UP Page Turning Partitions On or Off Selecting the operating System Selecting the Boot Partition Leaving MODIFY Mode Formatting Print Final Check Quitting Page CHAPTER FOUR ProDOS 8, DOS 3.3, Pascal, and CP/M Recognizing Vulcan under DOS Booting from a Vulcan DOS 3.3 Partition Patched DOS 3.3 Notes Volume Sizes Copying Files to the DOS 3.3 Partition Copying Files with FID To execute AE FlU Either: 1)Boot Vulcan’s DOS 3.3 floppy disk 2)Select AE FID from the main menu Page Page Other DOS 3.3 Goodies CHAPTER FIVE Number of Disks Required Suggested Backup Schedule Before You Back Up Running Backup Backup Entire Hard Disk Page Backup Modified Files Listing Files Restore Individual Files Page Page APPENDICES A- - Trouble Shooting B- - Vulcan Speed Under GS/OS C- - Hardware D- - A Brief Pro DOS Tutorial Page APPENDIX A Trouble Shooting Eight Total Drive Devices Two Drive Devices per Slot APPENDIX B Vulcan Speed Under GS/OS (IIGS Only) GS/OS Where to Put the Vulcan Driver APPENDIX C Accessing the Desk Accessory Classic Desk Accessories Menu Vulcan Main Menu Set Boot Partition Write Protect Partition Park Heads About Vulcan Where to Put the Vulcan Classic Desk Accessory APPENDIX D What They Do How To Set Them Push down on number side to Remote Light Jack APPENDIX E A Brief ProDOS Tutorial (file) (subdir.) GAS (subdir.) FAMOUS (subdir.) ProDOS Directory Structure Additional Resources APPENDIX F Getting Help