Arcam E-2 manual gm go gq, fr fs, gk ft, Control Connections, Trigger Outputs, gl gn

fm VCR OUT. Connect this to the S-video input of your video recorder.

fl TAPE. If you are using the tape loop for a secondVCR then connect the S-video from the VCR to this input.

HIGH QUALITY (COMPONENT) VIDEO CONNECTIONS

These inputs are suitable for connection to component (YUV/ YCrCb) or RGB outputs.These signals are usually available from a DVD player, set-top box or games console and offer the best possible picture quality.

Generally, the component video standard is used in North America/ NTSC regions, while RGB is used in Europe.

CONTROL CONNECTIONS

gl gn		RS232
		CONTROL
REMOTE
OUT	IN
	LOCAL	85 – 265VAC
		MAX 40VA

GROUND

12V INLIFT (IN)

TRIGGER ZONE 2

gm go gq

fr fs

HIGH QUALITY VIDEO

12

Y/G	U/B	V/R	Y/G	U/B	V/R
Y/G	U/B	V/R	Y/G	U/B	V/R
	OUT			3

gk ft

fr VIDEO 1, fs VIDEO 2, ft VIDEO 3 INPUTS. Connect these to the video outputs of your high quality video sources.

gk HIGH QUALITY VIDEO OUT. Connect these sockets to the component video inputs of your display device.

Important notes about HQ video inputs and outputs

When you connect your devices to these connectors, take care to follow the letter/colour coding for each input. No damage will occur if incorrectly connected, but unusually coloured or unstable pictures will result.

In the ‘Video Settings’ setup menu, each of these three high quality component video inputs can be individually allocated to one of the following inputs: DVD, SAT, TUNER, TAPE, CD, VCR or AV.

You cannot mix component and RGB sources.

The high quality component video inputs have sufficient bandwidth for line-doubled NTSC (525/60) or PAL (625/50) video and US HDTV video signals. However, when used with such signals the OSD is not overlaid on the picture but is output at standard interlaced NTSC or PAL (525 or 625 line) rate on a solid background.

Initially, the high quality video inputs are all disabled. Before any HQ video input can be selected it must be allocated to an input.

RGB 4-wire connection

Some video projectors and most European TV sets require the use of a 4-wire RGB connection, where the ‘sync’ signal is separate from RGB. In this case, you need to use the composite video MONITOR OUT 2 for the sync information. A special cable is available from your dealer for 4-wire RGB connection (refer to the table of SCART connections at the back of the manual).

gn IN LOCAL. Use with a local IR receiver when the AV8 front panel IR receiver is obstructed.

go IN ZONE 2. This allows the AV8 to be controlled remotely from zone 2 via infrared remote control.

A receiver compatible with this connector is available from Xantech (part no. 291-10). Please contact a Xantech registered dealer for this part, as ARCAM do not stock them. See www.xantech.com for more information.

The 3.5mm jack plug for this connector is wired as follows:

3.5mm stereo jack	Function
Tip	Signal
Ring	0V
Sleeve	12V, 30mA current-limited

This follows the Xantech standard for IR transmission over wire.

Connect to a remote IR receiver in zone 2 to allow control of the AV8 from zone 2.

gl (REMOTE) OUT. This enables control of the source components remotely from zone 2 or zone 1 using the local input. Control is possible by either connecting to the source devices via the 3.5mm IR jack (Arcam units only) or using an IR emitter stuck to the centre of the IR sensor window on the source component (such as a Xantech 283MW mini emitter).

gq RS232 CONTROL Use with control devices having an RS232 serial port (for example, Crestron and AMX touch screen controllers). This connection is also used for upgrading control software. See the sections at the end of this manual for control and programming information.

TRIGGER OUTPUTS

There are three trigger output sockets on the AV8, each of which is a 3.5mm stereo jack with two contacts, ‘tip’ and ‘ring’. See the tables for technical information on the trigger outputs.

gm 12V TRIGGER. Use for remotely turning on and off power amps or source equipment for the main zone and zone 2.

3.5mm stereo jack	Function	Voltage
Tip	Main zone on	On = 12V, 30mA
		Off = 0V
Ring	Zone 2 on	On = 12V, 30mA
		Off = 0V
Sleeve	Ground	0V

E-8

E-8