Manuals / AT&T / Communications / IP Phone

AT&T BCM50 manual Issue, Page 16 of, AT&T IP Flexible Reach Service

Models: BCM50

1 37

Download 37 pages 18.68 Kb

Page 16

AT&T IP Flexible Reach Service

Nortel BCM50 Release 3.0 SIP Configuration Guide

© 2007 AT&T Intellectual Property. All rights reserved. AT&T, the AT&T logo and all other AT&T marks contained herein are trademarks of AT&T Intellectual Property and/or AT&T affiliated companies. All other marks contained herein are the property of their respective owners.

Issue 0.7

Page 16 of 37

Image 16

AT&T manual Issue, Page 16 of, AT&T IP Flexible Reach Service, Nortel BCM50 Release 3.0 SIP Configuration Guide

Contents

AT&T VOIP Nortel BCM50 Release 3.0 SIP Configuration Guide For Use with AT&T IP Flexible Reach Service Issue 12/26/2007Issue Page 1 ofTABLE OF CONTENTS Special NotesTABLE OF FIGURES 1 Introduction 1.1 Pre-IP PBX Configuration Activity1.2 Customer Questions 1.4 Document Feedback 1.3 Trouble Reporting1.5 Document Change History Issue IssueDecember 12 Page 6 ofEmergency 911/E911 Services Limitations 2 Special NotesCalling Number Restricted / Private not supported BCM Soft Phones not currently supported3 Overview Figure 1 AT&T IP Flexible Reach Networko 12 digital station ports supporting digital phones PSTN Legacy PBX site with Cisco gateway Another BCM50 IP PBX site 4.1 Nortel BCM50 Version and Feature Requirements 4 Configuration GuideUpdate History UPDATE to FEPS Figure 3 BCM50 Lists of Applied PatchesPatch Name Version4.2 IP Trunks Figure 4 Available VoIP Trunks Figure 5 Application Resource availability of SIP or IP TrunksFigure 6 Assigning Line Pool to IP Trunks Figure 7 Assigning DN to Line PoolIssue AT&T IP Flexible Reach ServiceNortel BCM50 Release 3.0 SIP Configuration Guide Page 16 ofFigure 8 Configuring General DN Length Figure 9 Configuring Public Received Number Length and Dialing PlanFigure 10 Configuring Private Received Number Length Figure 11 Assigning a Route for IP Trunks Figure 12 Assign Code to Access IP Trunk Routes 4.3.1 Failover to Secondary AT&T IP Border Element IPBE 4.3 SIP Proxy ParametersFigure 13 Selecting IP Trunk Module Figure 14 Sip Proxy Parameters Figure 15 Outbound Proxy Table for failover to secondary AT&T IPBEs Configuration Æ Resources Æ Telephony Resources Disabled4.4 Media Parameters 1 st Preferred CodecFigure 17 Configuring analog DNs for fax Configuration Æ Resources Æ Telephony Resources 4.5 Port RangesFigure 18 Media Gateway Port Ranges 4.6 Configuring Outgoing Calls from BCM50 to AT&T IP Flex Reach ConfigurationÆ TelephonyÆ Sets Æ All DNsConfigurationÆ TelephonyÆ Sets Æ All DNs 4.7 Configuring Incoming Calls from AT&T IP Flex Reach to BCM50Figure 20 Configuring DID for Incoming Calls ConfigurationÆ TelephonyÆ Lines Æ Target Lines Figure 21 Display DID on IP Set LCDFigure 22 Assign Line Pool to IP Sets 5 Troubleshooting 5.1 System Monitoring with BCM MonitorBackward version compatibility is supported CPU utilization Physical memory Media card DSP utilization Issue AT&T IP Flexible Reach ServiceNortel BCM50 Release 3.0 SIP Configuration Guide Page 33 ofAdministrationÆ General ÆAlarms 5.2 Real-time display of BCM50 AlarmsFigure 28 BCM50 Alarms Page 5.3 Log Management Figure 29 Log Management6 APPENDIX A Configuring Destination Code with Wildcard Figure 30 Configuring Destination Code with WildcardEnd of Document