Manuals / AT&T / Communications / IP Phone

AT&T Real-time display of BCM50 Alarms, AdministrationÆ General ÆAlarms, BCM50 Alarms Page

Models: BCM50

1 37

Download 37 pages 18.68 Kb

Page 34

5.2 Real-time display of BCM50 Alarms

AT&T IP Flexible Reach Service

Nortel BCM50 Release 3.0 SIP Configuration Guide

5.2 Real-time display of BCM50 Alarms

AdministrationÆ General ÆAlarms

The BCM50 provides extensive alarm logs along with severity and problem descriptions. The following is an example screen shot of the “Alarms” display:

Figure 28: BCM50 Alarms Page

© 2007 AT&T Intellectual Property. All rights reserved. AT&T, the AT&T logo and all other AT&T marks contained herein are trademarks of AT&T Intellectual Property and/or AT&T affiliated companies. All other marks contained herein are the property of their respective owners.

Issue 0.7

Page 34 of 37

Image 34

AT&T manual Real-time display of BCM50 Alarms, AdministrationÆ General ÆAlarms, BCM50 Alarms Page

Contents

Issue AT&T VOIP Nortel BCM50 Release 3.0 SIP Configuration GuideFor Use with AT&T IP Flexible Reach Service Issue 12/26/2007 Page 1 ofTABLE OF CONTENTS Special NotesTABLE OF FIGURES 1 Introduction 1.1 Pre-IP PBX Configuration Activity1.2 Customer Questions 1.4 Document Feedback 1.3 Trouble Reporting1.5 Document Change History December 12 IssueIssue Page 6 ofCalling Number Restricted / Private not supported Emergency 911/E911 Services Limitations2 Special Notes BCM Soft Phones not currently supported3 Overview Figure 1 AT&T IP Flexible Reach Networko 12 digital station ports supporting digital phones PSTN Legacy PBX site with Cisco gateway Another BCM50 IP PBX site 4.1 Nortel BCM50 Version and Feature Requirements 4 Configuration GuideUpdate History Patch Name UPDATE to FEPSFigure 3 BCM50 Lists of Applied Patches Version4.2 IP Trunks Figure 4 Available VoIP Trunks Figure 5 Application Resource availability of SIP or IP TrunksFigure 6 Assigning Line Pool to IP Trunks Figure 7 Assigning DN to Line PoolNortel BCM50 Release 3.0 SIP Configuration Guide IssueAT&T IP Flexible Reach Service Page 16 ofFigure 8 Configuring General DN Length Figure 9 Configuring Public Received Number Length and Dialing PlanFigure 10 Configuring Private Received Number Length Figure 11 Assigning a Route for IP Trunks Figure 12 Assign Code to Access IP Trunk Routes 4.3.1 Failover to Secondary AT&T IP Border Element IPBE 4.3 SIP Proxy ParametersFigure 13 Selecting IP Trunk Module Figure 14 Sip Proxy Parameters Figure 15 Outbound Proxy Table for failover to secondary AT&T IPBEs 4.4 Media Parameters Configuration Æ Resources Æ Telephony ResourcesDisabled 1 st Preferred CodecFigure 17 Configuring analog DNs for fax Configuration Æ Resources Æ Telephony Resources 4.5 Port RangesFigure 18 Media Gateway Port Ranges 4.6 Configuring Outgoing Calls from BCM50 to AT&T IP Flex Reach ConfigurationÆ TelephonyÆ Sets Æ All DNsConfigurationÆ TelephonyÆ Sets Æ All DNs 4.7 Configuring Incoming Calls from AT&T IP Flex Reach to BCM50Figure 20 Configuring DID for Incoming Calls ConfigurationÆ TelephonyÆ Lines Æ Target Lines Figure 21 Display DID on IP Set LCDFigure 22 Assign Line Pool to IP Sets 5 Troubleshooting 5.1 System Monitoring with BCM MonitorBackward version compatibility is supported CPU utilization Physical memory Media card DSP utilization Nortel BCM50 Release 3.0 SIP Configuration Guide IssueAT&T IP Flexible Reach Service Page 33 ofAdministrationÆ General ÆAlarms 5.2 Real-time display of BCM50 AlarmsFigure 28 BCM50 Alarms Page 5.3 Log Management Figure 29 Log Management6 APPENDIX A Configuring Destination Code with Wildcard Figure 30 Configuring Destination Code with WildcardEnd of Document