Install Bottom Body PANEL/GREASE TRAY- ALL Models

STEP 10-INSTALL BOTTOM BODY PANEL/GREASE TRAY- (ALL MODELS)

•In upright position and drain hole toward the rear, slide Bottom Body Panel into guides (See Arrows) at bottom of Grill Body. Insert two #8 x 1/2” screws through the holes in guides and Bottom Body Panel; then tighten. Slide Foil Pan and Grease Tray all the way into Bottom Body Panel Brackets.

#8 X 1/2” SCREW (2pcs)

BOTTOM BODY PANEL

FOIL PAN

GREASE TRAY

STEP 11-INSTALL CERAMIC BRIQUETTE TRAYS & GRIDS - (ALL MODELS)

•Remove plastic completely from two Ceramic Briquette Trays. Place side by side on middle shoulder of front and rear firewall over the Burners.

•Place two Cooking Grids side by side on upper shoulder of front and rear firewall over the Ceramic Briquette Trays.

MIDDLE SHOULDER

UPPER SHOULDER

CERAMIC

BRIQUETTES

GRIDS

Page 20

Image 20

Aussie Kanga, Bonza Install Bottom Body PANEL/GREASE TRAY- ALL Models, Install Ceramic Briquette Trays & Grids ALL Models

Contents

AussieTM Important Safeguards Page Am 5 pm E.S.T Mon. Fri Telephone Kanga Bonza PART/DESCRIPTIONBonza PART/ Description QTY Kanga Bonza PART/ Descripton PART# QTY. Kanga Bonza 47 6mm Wheel LEG/ Side Table Assembly Tools Item 1, 2, or 4 Side Table X 1 3/8 Bolt 8pcs X 1 Bolt 8 pcs Fixed LEG/SIDE Table Assembly Tools Item 9 8 pcsItem 10 8 pcs Tear Drop Table Shown Legbrace Assembly Tools X 1 Bolt 8 pcs Pcs Bottom SHELF/LEG & Caster Assembly Tools Item 19, 20X 1 Bolt Wood LEG 1/4 x 1 3/8 Bolt Metal X 2 Bolt Wood 1/4 X 1 3/8 Bolt Metal WHEEL/ Cylinder Bracket Assembly Tools Item 23, 24Item 27 4 pcs X 1/2 Bolt Grill BODY/CART ASSEMBLY- Kanga Models Tools Assembly NextItem 30 Spacer 8 pcs Item 31 6mm x 110mm Bolt 8 pcs Item 32 6mm Wing NUT Assemble Grill Body to CART- Kanga Models 6mm X 110mm Item 31 Actual Size 6mm x 110mm Bolt Pcs Grill BODY/CART ASSEMBLY- Bonza & Bonza Deluxe Models ToolsItem 32 6mm Wing NUT 8pcs 6mm x 110mm Bolts Grill BODY/CART ASSEMBLY- Bonza ModelsContinue Assembly of Bonza & Bonza Deluxe Models AT Step Install Burner Tools Attach Decorative Privacy Panel to Cart ALL ModelsNext Or 4 PCS 16 GAP Adjust Tab if greater than 3/16Cotter PIN Install from underneath Backside of grill #8 X 1/2 Screw 2pcs Install Bottom Body PANEL/GREASE TRAY- ALL ModelsInstall Ceramic Briquette Trays & Grids ALL Models #10 X 3/8 Screw Attach Handle to Weather Cover LID Kanga Models ToolsSCREW, #10 X 3/8 Attach Handle and Heat Indicator to Hood Bonza Models Tools Attach LP Cylinder to Grill ALL Models FIG. K Leak Testing to be Performed in a WELL-VENTILATED Area How to perform a leak test LP Gas Cylinder Connecting/ Disconnecting LP Gas Cylinder to GrillGAS, CYLINDER, Hose Regulator Information Selecting a Location Before Using Your LP GAS GrillPrecautions LeakTesting Operating the LP GAS Grill Lighting the Grill Using the Integra Spark Ignition System Preparation Before CookingTurn LP cylinder handle counter-clockwise on Confirm each burner is lit before lighting another burner Manual Lighting of the Grill Care and Maintenance Check Your Flame End of Cooking SessionTurn off Your LP Gas Grill Grill Cooking Burner Maintenance How to clean procelain coated cast iron burners Cleaning the Grill Body Preventive MaintenanceCeramic Briquettes Bottom Panel/ Grease Tray Using the ignitor Using a matchBurners will not light Low flame or low heat Persistent grease fire Flames blow outFlare up Important Notice Aussie Grill Company Limited Warranty

Aussie Kanga, Bonza Install Bottom Body PANEL/GREASE TRAY- ALL Models, #8 X 1/2 Screw 2pcs

Models: Bonza Kanga Bonza Deluxe

STEP 10-INSTALL BOTTOM BODY PANEL/GREASE TRAY- (ALL MODELS)

#8 X 1/2” SCREW (2pcs)

STEP 11-INSTALL CERAMIC BRIQUETTE TRAYS & GRIDS - (ALL MODELS)