AussieTM | Aussie Bonza Deluxe, Kanga instruction

AussieTM

LP Gas Grill

Assembly and Use Manual

Bonza

©Aussie™ Grill Company 2001

For Customer Service, call

1-800-251-7558

www.aussiegrill.com

Bonza Deluxe

Kanga

This owners manual is intended for the following models:

7462, 7402, 7362, 7302, 7262, 7202

•READ AND FOLLOW INSTRUCTIONS CAREFULLY BEFORE ASSEMBLY OR USE. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN DEATH, SERIOUS BODILY INJURY, AND/OR PROPERTY LOSS.

•FOR OUTDOOR HOUSEHOLD USE ONLY. NOT FOR COMMERCIAL USE. •SOME PARTS MAY CONTAIN SHARP EDGES - ESPECIALLY WHERE NOTED IN THIS MANUAL! WEAR PROTECTIVE GLOVES IF NECESSARY. •THESE INSTRUCTIONS MUST BE KEPT WITH THE CONSUMER AND RETAINED FOR FUTURE USE.

•PORCELAIN COATING CAN CHIP DURING ASSEMBLY. WEAR SAFETY GLASSES WHILE ASSEMBLING GRILL.

FOR YOUR SAFETY

If you smell gas:

1.Shut off gas to the appliance.

2.Extinquish any open flame.

3.Open Lid.

4.If odor continues, immediately call your gas supplier or your fire department.

FOR YOUR SAFETY

1.Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

2.An LP cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.

Image 1

Aussie Bonza Deluxe, Kanga owner manual AussieTM

Contents

AussieTM Important Safeguards Page Am 5 pm E.S.T Mon. Fri Telephone Bonza PART/DESCRIPTIONKanga Bonza QTY Kanga Bonza PART/ Description PART/ Descripton PART# QTY. Kanga Bonza 47 6mm Item 1, 2, or 4 Side Table X 1 3/8 Bolt 8pcs X 1 Bolt 8 pcs Wheel LEG/ Side Table Assembly Tools Item 9 8 pcs Fixed LEG/SIDE Table Assembly ToolsItem 10 8 pcs Tear Drop Table Shown X 1 Bolt 8 pcs Pcs Legbrace Assembly Tools Item 19, 20 Bottom SHELF/LEG & Caster Assembly ToolsX 1 Bolt Wood LEG 1/4 x 1 3/8 Bolt Metal X 2 Bolt Wood 1/4 X 1 3/8 Bolt Metal Item 23, 24 WHEEL/ Cylinder Bracket Assembly ToolsItem 27 4 pcs X 1/2 Bolt Assembly Next Grill BODY/CART ASSEMBLY- Kanga Models ToolsItem 30 Spacer 8 pcs Item 31 6mm x 110mm Bolt 8 pcs Item 32 6mm Wing NUT 6mm X 110mm Assemble Grill Body to CART- Kanga Models Item 32 6mm Wing NUT 8pcs Grill BODY/CART ASSEMBLY- Bonza & Bonza Deluxe Models ToolsItem 31 Actual Size 6mm x 110mm Bolt Pcs Continue Assembly of Bonza & Bonza Deluxe Models AT Step Grill BODY/CART ASSEMBLY- Bonza Models6mm x 110mm Bolts Attach Decorative Privacy Panel to Cart ALL Models Install Burner ToolsNext Or 4 PCS Cotter PIN Install from underneath Backside of grill Adjust Tab if greater than 3/1616 GAP Install Ceramic Briquette Trays & Grids ALL Models Install Bottom Body PANEL/GREASE TRAY- ALL Models#8 X 1/2 Screw 2pcs SCREW, #10 X 3/8 Attach Handle to Weather Cover LID Kanga Models Tools#10 X 3/8 Screw Attach Handle and Heat Indicator to Hood Bonza Models Tools FIG. K Attach LP Cylinder to Grill ALL Models How to perform a leak test Leak Testing to be Performed in a WELL-VENTILATED Area GAS, CYLINDER, Hose Regulator Information Connecting/ Disconnecting LP Gas Cylinder to GrillLP Gas Cylinder Precautions Before Using Your LP GAS GrillSelecting a Location Operating the LP GAS Grill LeakTesting Preparation Before Cooking Lighting the Grill Using the Integra Spark Ignition SystemTurn LP cylinder handle counter-clockwise on Confirm each burner is lit before lighting another burner Manual Lighting of the Grill Check Your Flame End of Cooking Session Care and MaintenanceTurn off Your LP Gas Grill Grill Cooking How to clean procelain coated cast iron burners Burner Maintenance Preventive Maintenance Cleaning the Grill BodyCeramic Briquettes Bottom Panel/ Grease Tray Using a match Using the ignitorBurners will not light Low flame or low heat Flare up Flames blow outPersistent grease fire Important Notice Aussie Grill Company Limited Warranty