User Manual
Item | Description |
|
|
You are supplying a user name and password now.
The utility prompts you for them each time you try to connect to a network.
2.To provide a user name and password now, enter them in the fields provided.
Not all values for Authentication Mode are available for all Security settings.
Enable CCX mode: Enables connections in CCX mode. When checked, additional authentication modes are available.
This checkbox is only enabled when Super Profile is set to Enterprise. Configure: Click Configure to open the configuration window.
Open Advanced Mode: Click Open Advanced Mode to configure the following screen：
|
|
|
|
| Power Save Mode: Indicates whether to use power saving. This field can | ||||||||
|
|
|
|
| be one of the following: | ||||||||
|
|
|
|
| None: No power save mode. | ||||||||
|
|
|
|
| Max: Max power save mode. | ||||||||
|
|
|
|
| TX Power Level: The transmit power level, which can be one of the | ||||||||
|
|
|
|
| following: | ||||||||
|
|
|
|
| Low Power (6% of full power) | ||||||||
|
|
|
|
|
| ||||||||
|
|
|
|
|
| ||||||||
|
|
|
|
|
| ||||||||
|
|
|
|
| High Power (100%) | ||||||||
|
|
|
|
| TX Rate: The preferred rate of transmission, in Mbps. The options for this | ||||||||
|
|
|
|
| field are based on the selected band and channel, | ||||||||
|
|
|
|
| Packet Burst: Indicates whether the Packet Bursting feature is enabled. | ||||||||
|
|
|
|
| Turbo Mode: Indicates whether the 4X feature is enabled. | ||||||||
|
|
|
|
| Fragment Threshold: The maximum fragment length, in bytes. The value | ||||||||
|
|
|
|
| is an even number from 256 to 4096 (default is 4096). | ||||||||
|
|
|
|
| RTS Threshold: The minimum packet length for sending an RTS frame, | ||||||||
|
|
|
|
| in bytes. The value must be greater than 0 (default is 4096). | ||||||||
|
|
|
|
| Preamble: Either short or long | ||||||||
|
|
|
|
| Retry limits: The number of retries to attempt, if necessary, when | ||||||||
|
|
|
|
| sending a frame. There are two Retry limits fields: | ||||||||
|
|
|
|
| Short: For frames without an RTS frame | ||||||||
|
|
|
|
| Long: For frames with an RTS frame | ||||||||
|
|
|
| To hide the advanced fields, click Close Advanced Mode. | |||||||||
|
|
|
|
| OK: | When the configuration is done, click | OK | to save. | |||||
|
|
|
|
| Cancel: | Click | Cancel | to discard changes. | |||||
|
| Rescan |
|
| Searches | for all available networks. Clicking on the button, the device will | |||||||
|
|
|
|
| start to rescan and list all available sites. | ||||||||
| Configure |
| Click | Configure | to modify the settings for the profiles with the SSID of the | ||||||||
|
|
|
|
| selected network. | ||||||||
|
|
|
|
| If no profile exists, the Profile Configuration window is displayed so that | ||||||||
|
|
|
|
| you can create a profile. The Profile Name field is blank. | ||||||||
|
|
|
|
| If profile exists, the Profile Configuration window is displayed so that | ||||||||
|
|
|
|
| you can modify its settings. | ||||||||
Page 20 of 24
